|
Controller Port 4 and 5: both for Z axis?
|
|
1
|
44
|
April 12, 2020
|
|
Need help: print M5 bolt
|
|
8
|
86
|
April 12, 2020
|
|
FYI Repair tutorial for Snapmaker Original
|
|
2
|
134
|
April 11, 2020
|
|
FYI: FAQs for Snapmaker Original
|
|
1
|
143
|
April 11, 2020
|
|
Z Axis Problem Nozzle Doesn’t Print Close Enough To Heated Bed
|
|
12
|
80
|
April 8, 2020
|
|
Bed level from a PC
|
|
3
|
92
|
April 8, 2020
|
|
Enclosure door open contact: is relly needed?
|
|
6
|
61
|
April 8, 2020
|
|
FYI How to turn off the door detection in Snapmakerjs
|
|
1
|
39
|
April 7, 2020
|
|
Linear Actuator
|
|
4
|
359
|
April 6, 2020
|
|
E3D Titan / V6 Mount
|
|
28
|
2520
|
April 5, 2020
|
|
Enclosure and FW/SW
|
|
5
|
72
|
April 3, 2020
|
|
S.O.S: Just arrived but... can't print 3DBench!
|
|
12
|
114
|
April 2, 2020
|
|
Excessive squeaking when printing
|
|
3
|
68
|
April 1, 2020
|
|
Machine protection feature
|
|
1
|
36
|
April 1, 2020
|
|
Heat bed stopped heating
|
|
15
|
1054
|
March 26, 2020
|
|
Larger prints "shift" forward
|
|
5
|
86
|
March 25, 2020
|
|
Everything is about .4 mm too big
|
|
4
|
77
|
March 25, 2020
|
|
Touchscreen not reacting
|
|
10
|
445
|
March 25, 2020
|
|
3D prints are turning out badly
|
|
16
|
1046
|
March 22, 2020
|
|
Anyone tested cutting Aluminium
|
|
25
|
6817
|
March 19, 2020
|
|
Cura and an odd finish
|
|
7
|
89
|
March 18, 2020
|
|
Flash drive was pulled while printing
|
|
3
|
71
|
March 16, 2020
|
|
How can I tell if my laser is bad?
|
|
13
|
205
|
March 12, 2020
|
|
Need a new print nozzle
|
|
8
|
162
|
March 10, 2020
|
|
Reducing Sonic Emissions
|
|
28
|
1960
|
March 9, 2020
|
|
Filament Struck inside the Extruder
|
|
9
|
187
|
March 6, 2020
|
|
How can I tell if my printer is updated?
|
|
4
|
167
|
March 4, 2020
|
|
Not able to activate the door detection
|
|
7
|
359
|
March 4, 2020
|
|
Calibration new build SnapMaker 1.0 does not succeed
|
|
3
|
85
|
March 2, 2020
|
|
CNC bit not rotating when using fusion 360 file
|
|
1
|
83
|
February 28, 2020
|
