Snapmaker 2.0
Product Feedback Give feedback about Snapmaker devices and addons. Getting Started Get help from fellow creatives.
Topic | Replies | Views | Activity | |
---|---|---|---|---|
2.0 Wiki Content Updates
Dear 2.0 Makers, We will post the related link in this thread once there’s new content for 2.0 in Snapmaker Wiki. Currently, the majority of content for 2.0 is still in the Support Center, but will gradually be migrate… |
![]() ![]() ![]() ![]() |
18 | 3127 | August 26, 2024 |
Collection Of Guide Links
I figure it might be good to start a topic that sort-of compiles useful guides together to make them easier to find, since the forum doesn’t allow signatures and guides can just disappear into the void. As such, in this … |
![]() ![]() ![]() ![]() ![]() |
13 | 5354 | January 3, 2025 |
Summary: Extruder calibration a must
The topic known as: has become very useful to point people to so that they can calibrate their e-steps. However, that topic has become a bit large and overwhelming for a newcomer. So I’m starting this topic as an easie… |
![]() ![]() ![]() ![]() ![]() |
39 | 20232 | May 9, 2025 |
Snapmaker 2.0 Firmware Updates and Downloads
We will release the latest Snapmaker 2.0 firmware updates and downloads under this topic. Your feedback is very much appreciated. You can report any bugs or make any suggestions in the discussion thread. Snapmaker 2.0 F… |
![]() ![]() ![]() ![]() |
35 | 151704 | July 18, 2024 |
Firmware images |
![]() ![]() ![]() ![]() ![]() |
20 | 2028 | May 28, 2025 |
Laser Frustrations and bugs |
![]() ![]() ![]() |
12 | 221 | May 27, 2025 |
Door detection cannot be turned off at all |
![]() ![]() ![]() ![]() ![]() |
14 | 1336 | May 25, 2025 |
Filament Runout Recovery error while Laser Engraving |
![]() ![]() ![]() ![]() ![]() |
20 | 266 | May 25, 2025 |
Discussion of Snapmaker 2.0 Firmware Updates |
![]() ![]() ![]() ![]() ![]() |
767 | 44374 | May 23, 2025 |
1064nm IR+20/40W + Lightburn Guide |
![]() ![]() ![]() ![]() ![]() |
68 | 3627 | May 22, 2025 |
A350 3DP cube sizes off |
![]() ![]() ![]() |
3 | 80 | May 22, 2025 |
Dual Extruder First Layer Issue |
![]() ![]() ![]() ![]() ![]() |
29 | 1491 | May 20, 2025 |
Snapmaker Vinyl Cutter Attachment |
![]() ![]() ![]() ![]() ![]() |
58 | 9915 | May 18, 2025 |
Dual extruder oozing during print |
![]() ![]() ![]() |
9 | 112 | May 17, 2025 |
Dual Extruder sensor loose? |
![]() ![]() |
3 | 121 | May 14, 2025 |
Need Parameter Advice |
![]() ![]() ![]() ![]() |
5 | 109 | May 12, 2025 |
Yeti engraving settings for 10W Diode or 2W IR |
![]() ![]() |
1 | 102 | May 12, 2025 |
Prime Tower always falls over |
![]() ![]() ![]() ![]() ![]() |
9 | 756 | May 11, 2025 |
Laser cutting items longer than the cutting bed? Repositioning for two step cut |
![]() ![]() |
1 | 224 | May 9, 2025 |
Should we release the new firmware with Vibration Compensation to all users, despite its current limitations? Vote here |
![]() ![]() ![]() ![]() ![]() |
15 | 472 | May 7, 2025 |
Multi-Color Printing for first layer on Snapmaker Using OrcaSlicer + Virtual Extruders (with M600) |
![]() |
0 | 118 | May 6, 2025 |
Display defekt?! |
![]() ![]() ![]() |
2 | 89 | April 29, 2025 |
Sandwich laser platform |
![]() ![]() |
4 | 140 | May 5, 2025 |
Inconsistent Layerlines |
![]() ![]() ![]() ![]() ![]() |
49 | 328 | May 5, 2025 |
Guide for Non-Planar Laser Engraving |
![]() ![]() ![]() ![]() ![]() |
17 | 3341 | May 5, 2025 |
Issues Report & Discussion on Vibration Compensation Firmware V2.3.1 for Snapmaker 2.0 Series |
![]() ![]() ![]() ![]() ![]() |
8 | 334 | May 2, 2025 |
Send G-code to device via serial connection (Snapmaker 2.0 A350) |
![]() ![]() |
12 | 95 | May 1, 2025 |
Snapmaker 2.0 A350 Modifications |
![]() ![]() ![]() ![]() ![]() |
8 | 2216 | April 30, 2025 |
USB port stopped working |
![]() ![]() ![]() ![]() ![]() |
7 | 691 | April 29, 2025 |
Dear Snapmaker enthusiast & People in Snapmaker |
![]() ![]() ![]() ![]() ![]() |
8 | 303 | April 29, 2025 |