Snapmaker 2.0 (3-in-1) Snapmaker2.0 Troubleshooting guides
| Topic | Replies | Views | Activity | |
|---|---|---|---|---|
|
Collection Of Guide Links
I figure it might be good to start a topic that sort-of compiles useful guides together to make them easier to find, since the forum doesn’t allow signatures and guides can just disappear into the void. As such, in this … |
|
12 | 5931 | January 3, 2025 |
|
Summary: Extruder calibration a must
The topic known as: has become very useful to point people to so that they can calibrate their e-steps. However, that topic has become a bit large and overwhelming for a newcomer. So I’m starting this topic as an easi… |
|
40 | 21834 | February 15, 2026 |
|
About the Snapmaker2.0 Troubleshooting guides
Find solutions to your issues or share suggestions for improvement here! If your problem has been resolved, please add the appropriate tags and move your post to this section. Contact official support to log your i… |
|
3 | 2694 | June 30, 2019 |
|
Long duration prints fail randomly
|
|
6 | 190 | November 9, 2026 |
|
3D print - prints off center halfway, seems to try and push the printhead past the rail
|
|
11 | 145 | November 3, 2026 |
|
Help! Still Learning to Print
|
|
4 | 111 | October 14, 2026 |
|
Air assist hose fitting for 40W laser
|
|
1 | 78 | October 3, 2026 |
|
Power problems with Snapmaker 2
|
|
3 | 99 | October 1, 2026 |
|
New assembly of V 1.8 machine
|
|
3 | 142 | September 3, 2026 |
|
New assembly frozen screen
|
|
5 | 151 | September 3, 2026 |
|
Snapmaker A350 Platform Not Flat - The Nuclear Option
|
|
12 | 511 | August 17, 2026 |
|
45 degree print error
|
|
5 | 135 | June 26, 2026 |
|
Phantom lines in graphic on preview
|
|
4 | 103 | June 13, 2026 |
|
Liniar module
|
|
4 | 126 | June 1, 2026 |
|
Rotary issues?
|
|
12 | 221 | April 25, 2026 |
|
Issue Removing Print From Print Bed
|
|
13 | 221 | March 2, 2026 |
|
Problems calibrating
|
|
2 | 111 | February 21, 2026 |
|
Dual Extruder Calibration Issues
|
|
7 | 200 | February 18, 2026 |
|
Dual Extruder loses Z axis position on extruder change
|
|
13 | 246 | February 15, 2026 |
|
New Module IDEAS
|
|
117 | 15367 | February 13, 2026 |
|
Need a second opition on hot end
|
|
2 | 104 | January 12, 2026 |
|
Laser just cut a short line during camera paper test
|
|
9 | 187 | January 5, 2026 |
|
Prusa Slicer Horrible movement noise. A350
|
|
10 | 180 | January 4, 2026 |
|
Forum Terms & Rules
|
|
18 | 1817 | January 3, 2026 |
|
Should (0,0,0) on the printer bed be close to (0,0,0) on the controller?
|
|
5 | 546 | December 29, 2025 |
|
Dual extrusion calibration not adhering
|
|
4 | 169 | December 24, 2025 |
|
A350 Stopped an goes to home after short time of Start
|
|
5 | 192 | December 17, 2025 |
|
Everything was printing perfectly until it wasn't
|
|
9 | 254 | November 27, 2025 |
|
Bad first layer on a350
|
|
1 | 96 | November 19, 2025 |
|
2.0 a350 duel extrusion bad prints
|
|
5 | 130 | November 18, 2025 |