Snapmaker 2.0 (3-in-1)
Snapmaker2.0 Featured Showcase Collection Snapmaker2.0 Troubleshooting guides Find solutions to your issues or share suggestions for improvement here! If your problem has been resolved, please add the appropriate tags and move your post to this section. Update - Snapmaker2.0（3-in-1） Get the latest official updates.
| Topic | Replies | Views | Activity | |
|---|---|---|---|---|
|
Guide: Automatic Start via Drag/Drop
This is the “wireless” portion to round out my full Lightburn control guide, found here: Since my main snapmaker (pretty much stays setup with the 10W + Enclosure) is far away from my PC, using a cable + Lightburn isn… |
|
31 | 3816 | December 7, 2025 |
| Filament guide |
|
0 | 8 | February 3, 2026 |
| Beginners Guide for Snapmaker 2.0 |
|
6 | 39 | February 3, 2026 |
| Printing men’s shoes |
|
1 | 47 | February 2, 2026 |
| Auto Deploying Touch Bed Leveling Mod For SM 2.0 |
|
1 | 60 | February 1, 2026 |
| A250 Recovery After Fire |
|
7 | 63 | February 1, 2026 |
| Firmware beta for Snapmaker 2.0! 2025-12-31 |
|
13 | 748 | January 31, 2026 |
| Snapmaker 2.0 A350 Modifications |
|
11 | 4072 | January 29, 2026 |
| Vibration Compensation Firmware Open Beta for 2.0 Series (A/AT/F Models) |
|
140 | 10960 | January 28, 2026 |
| Live Z offset gcode command |
|
3 | 52 | January 28, 2026 |
| Printer loses bed leveling |
|
8 | 73 | January 27, 2026 |
| Full Lightburn Control Guide |
|
549 | 37036 | January 26, 2026 |
| Hot bed nor Hot end heating? |
|
2 | 32 | January 26, 2026 |
| Burnt 3mm MDF 40W |
|
4 | 104 | January 26, 2026 |
| Calibration and Printing Issues |
|
8 | 61 | January 25, 2026 |
| 1064nm IR+20/40W + Lightburn Guide |
|
123 | 5871 | January 25, 2026 |
| My Enclosure exhaust system - fits under garage door |
|
7 | 6214 | January 24, 2026 |
| Extending the Lifetime of the Snapmaker Air Purifier Filter Cartridge with Reusable Pre-Filters |
|
1 | 30 | January 21, 2026 |
| Feature Request: Pause at Layar |
|
4 | 59 | January 21, 2026 |
| Laser Engraving on a Tapered Tumbler |
|
1 | 49 | January 19, 2026 |
| Lightburn Camera choices and Mounting |
|
1 | 61 | January 19, 2026 |
| Replacement plate for the A250 |
|
1 | 38 | January 19, 2026 |
| Adhesions issues/bed leveling |
|
8 | 1327 | January 18, 2026 |
|
Summary: Extruder calibration a must
The topic known as: has become very useful to point people to so that they can calibrate their e-steps. However, that topic has become a bit large and overwhelming for a newcomer. So I’m starting this topic as an easi… |
|
41 | 21016 | November 16, 2025 |
| Extruder Calibration a must |
|
286 | 44356 | January 17, 2026 |
| Qucik swap problem |
|
2 | 48 | January 16, 2026 |
| 3D Printing - Nothing happens after starting |
|
24 | 1754 | January 15, 2026 |
| Dual extruder bed leveling gcodes missing |
|
15 | 220 | January 14, 2026 |
| Need a second opition on hot end |
|
2 | 50 | January 12, 2026 |
| Rough surface |
|
1 | 45 | January 11, 2026 |