So, we got our A350 3 days ago and after much twiddling, have made some progress, but are still struggling with adhesion and have not been able to get a successful calibration print yet. Setting the myriad other issues aside, I think the z-axis level might be an issue, but at this point have no tru…

i responded to brent accidently. you have an installation issue: [image] [image] your linear modules are not in the grooves properly, they are offhanging the plate. but yeah, the snapmaker pla that came in the box is also a major issue. additional spools purchased are ok but the one in the main …

Yes its correct, you must calibrate the last point manualy, to set the proper z height. You can set the autocalibration off with the touchpad under settings 3d printer. Then you can choose how many points are beeing used to calibrate the bed.

Sorry stefix - didnt mean to reply to you. Mouriana Auto calibration, if everything is proper, is not terrible. Its not the best, but shouldnt be crashing. Firstly: the position of the last calibration point is not dead center, because the sensor on the 3dp module is also off center. no worries …

Thank you MooseJuice, and sorry so long to reply. We were getting frustrated and I had to step away before I broke something. :stuck_out_tongue: Knowing that the last position is not dead center is good. I wasn’t sure about that, and it helps me have a little relief. The last calibration point is …

I commend your ability to walk away from the frustration without smashing the machine, know that you are not the only person who has had to do so. Feel free to manually level it, but if your nozzle is crashing it sounds like something is assembled wrong or the sensor needs adjusted. I would presum…

Yes, I forgot to mention that we made sure the bed was installed correctly. And yes, I downloaded the update manually and installed via USB. And yes, those are the instructions I used. They are very poorly written, but between that and some other helpful forum posts, I’ve been able to suss it out.…

I should also note that I know that adhesion is a complex thing; that is one of the frustrating things about this process. Is it the cheap Snapmaker PLA? Is it the room temp? Bed temp? 1st layer speed? Extruder speed? Nozzle temp? Software or hardware issues? Our overall ignorance? Our ninja cats br…

4 screw holes on the tool head, go in 4 holes on the mount [image] Pictures for reference [image] [image] Snapmaker 2.0 3D Printing V1.0.0 3D Printing 1 Set Up for First Use Read the product Quick Start Guide (https://snapmaker.com/product/snapmaker-2/downloads) to check the included pa…

Your linear module is not right. [image] They are sticking out past the build plate. they should be sitting flush inside the grooves

I say we first get your machine assembled properly, then we can redo the calibrations and try again try to print a calibration cube from thingiverse first to start with after doing the calibration as discussed XYZ 20mm Calibration Cube by iDig3Dprinting - Thingiverse From there you should see suc…

OH! Thanks! Fudge, I can’t believe we didn’t notice that!

Auto-leveling is...wonky

Snapmaker 2.0 (3-in-1) Snapmaker2.0 Troubleshooting guides

brent113 December 29, 2020, 2:12am 18

Cubes are out. Loooong cubes are in Printing very skewed

Topic		Replies	Views
Autolevel Problem Snapmaker 2.0 (3-in-1)	6	642	February 23, 2021
Auto-level runs, but print starts much to high Snapmaker 2.0 (3-in-1)	2	379	April 23, 2022
Calibration pushing deep into buildplate Snapmaker 2.0 (3-in-1)	106	10555	December 28, 2021
Leveling / First layer Problems Snapmaker2.0 Troubleshooting guides	39	3285	July 19, 2021
Please help me with bed leveling first layer mess uneven Snapmaker 2.0 (3-in-1)	53	3251	January 7, 2023

Auto-leveling is...wonky

Related topics