I live in an apartment, and need a surface for my Artisan that’s big enough, but not bigger than it needs to be. To have room for the Controller and a little clearance for the wires, 36" by 42" seems like the ideal size (but I’m open to other options!). I have not been able to find a quality table …

Bought a Ikea Bror and put a bigger tabletop on it. Also cut the legs, but that was just my preference. Very stable and not that expensive.

@elopan Sorry if this is a dumb question, but how did you attach the bigger tabletop to the Bror? Also, where’d you get your tabletop? Unfortunately all the ones I found on Ikea and elsewhere don’t have enough depth to fit the Artisan. Thanks so much for the help!

You can either screw it from the bottom side up or just use strong double sided tape. Took some tabletop from ikea, but got the controller on a seperate table. You can however just go to some carpenter or joiner craftsmen, usually a plain tabletop shouldnt cost much. Here a lot of hardware stores a…

You can always build one from your local DIY store in timber frame. I have gone for 3030 aluminium on levelling castors should I need to move it for any reason. Not completely finished yet, the controller will be placed under the printer with a drawer runner, then it will be space for filament and…

I got sick of looking for tables that would fit my artisan. Just decided to make one. It’s not finished since its part of a full garage build out but this is the start. [20230507_165250]

I have built the mobile table from 30x30 aluminum profiles. The walls are made of Aludibond with magnetic holders attached, so you can remove all sides quickly and easily to get to the lower table. The controller is embedded in the door and can be operated from the outside. The Snapmaker air filter …

does anyone have a solution fpr these problem? [image] pause at height Snapmaker Artisan Hello everyone, I recently got an artisan. before the artisan I worked with prusa slicer and put the break to insert a nut over the slicer. Now I have installed the Cura Pugin and try…

I custom-built my desk from finger-jointed pine panels and H2 construction lumber. Our local hardware store chain, Bunnings, sells these really handy panels for desks, tabletops and kitchen counters that are pre-jointed and cut to size. I used a 2100x600mm panel for the section where my computer mo…

I used an Idea from the Facebook Group. Credits here to: Silke Handke! Base plate: Multiplex board 100cm x 120cm x 2.4cm Cabinets: 3x Cabinets from Sweden :wink: Ground plate: Multiplex Board 78cm x 116cm x 1.5cm Small piece of carpet to protect the floor with the same size as the base plate. […

I h [Screenshot_2023-06-11-04-14-57-54_b5f6883d2c20a96c53babc0b4ac88108] ad a sturdy adjustable height lab work bench with a top that was about 8 inches too narrow and found a table top on Amazon that fits well. The Amazon description is: Visit the VIVO Store VIVO Universal 71 x 36 inch Table …

What are you putting your Artisan on? I'm losing my mind trying to find a properly sized table or desk for it

Artisan (3-in-1)

brainson May 8, 2023, 6:55pm 8

does anyone have a solution fpr these problem?

Topic		Replies	Views
Artisan volume and surface requirements Artisan (3-in-1)	11	1248	January 23, 2023
Where is the table that I can buy? Snapmaker2.0 Troubleshooting guides	23	2140	January 1, 2022
Storage bracket for Artisan module Showcases & Tips Accessories	3	659	November 8, 2023
A350 noisy during print Snapmaker 2.0 (3-in-1)	9	690	December 15, 2020
Artisan: Price is out Artisan (3-in-1)	22	1783	August 2, 2022

What are you putting your Artisan on? I'm losing my mind trying to find a properly sized table or desk for it

Related topics