Snapmaker 2.0 Firmware Updates and Downloads

Jul 24 2020: Snapmaker2_V1.10.0

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Here comes the latest version of the Snapmaker 2.0 firmware. Your feedback is always appreciated.

Changelog:

Main Controller

Bug Fixes

  • Fix a bug where the controller doesn’t enable wait-events after refactoring.
  • Fix a bug where a Z-Offset with a negative value can not be applied during the printing process or recovered from Power-Loss.
  • Fix a bug where the last G-code command might not be performed if printing from the touchscreen.

Improvements

  • Reduce the maximum Y position for 4mm to prevent the slider from hitting the end of the slot on the Y linear module for the A150 model.

Touchscreen

Bug Fixes

  • Fix a bug where renaming file extension will cause the file not to be displayed on the Files page.

Improvements

  • Unify print file source.
    • Now the touch screen will not trigger “finish print job” popup if a USB disk is disconnected from the controller.

Downloads:

Snapmaker2_V1.10.0

MD5: ececcc9e0b491f19f548616fb8bd23c1

Notes:

This firmware update is only compatible with the Snapmaker 2.0 devices.

You can check the About page for the firmware version after the upgrade.

How to update Firmware

  • via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug USB into the USB slot of the Controller.
    • On the touchscreen, tap Files , select the update file under the USB tab to start the update.
  • via Wi-Fi
    • Tap Settings -> Firmware Update on the touch screen.
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, click “Update Now” to start the update.
4 Likes

Sep 1 2020: Snapmaker2_V1.10.1

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Here comes the latest version of the Snapmaker 2.0 firmware. Your feedback is always appreciated.

Changelog:

Main Controller

Bug Fixes

  1. Fix a bug where the machine stops at 99% when 3D printing.
  2. Filament would extrude properly after resuming from Pause or Power-Loss Recovery.

Improvements

  • Thermal protection is optimized to avoid accidental triggers.
  • Confirm if Power-Loss Recovery is normal during controller bootup.
  • Pre-heat the nozzle to 150℃ before it raises up from the print after resuming from Power-Loss Recovery.
  • Lower the initial height of the nozzle after Auto Leveling.
  • Raise 3mm for the initial height of the nozzle in Manual Leveling.

Downloads:

Snapmaker2_V1.10.1

MD5: 6addea2ecc4a06ed07c138dfa4b3a502

Notes:

This firmware update is only compatible with the Snapmaker 2.0 devices.

You can check the About page for the firmware version after the upgrade.

How to update Firmware

  • via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug USB into the USB slot of the Controller.
    • On the touchscreen, tap Files , select the update file under the USB tab to start the update.
  • via Wi-Fi
    • Tap Settings -> Firmware Update on the touch screen.
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, click “Update Now” to start the update.
9 Likes

Feb 3 2021: Snapmaker2_V1.11.4

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

Bug Fixes

  • Fix a bug where CNC spindle keeps rotating despite machining session being terminated.
  • Reduce sensitivity of heating protection for hot end to avoid false triggering.

Improvement

  • Reduce debounce time for unplug detection of Touchscreen from 10 s to 100 ms.

Touchscreen

New Features

  • Add Japanese and Simplified Chinese.
    • You can change the language settings through Settings > Language > language applicable > Save .

Bug Fixes

  • Fix a bug where Go To Work Origin starts without registering current toolhead position. Now if in Z orientation the newly set work origin is
    • lower than current position, the toolhead will move in X and Y orientations first.
    • higher than current position, the toolhead will move in Z orientation first.
  • Fix a bug where Run Boundary may cause Touchscreen to crash.
  • Fix a bug where swiping to rename folder in Files fails.

Improvements

  • Improve Wi-Fi connection and remote access from Snapmaker Luban.

Downloads

Snapmaker2_V1.11.4

MD5: a712a418c4cd9e01e8f9708ec3f4fdbf

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .
6 Likes

Mar 31 2021: Snapmaker2_V1.12.0

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Notice
Please read this article before you upgrade firmware to V1.12.0.

Changelog

General

New Features

  • Add support for the Rotary Module.
  • Add support for the Emergency Stop Button.

Controller

New Features

  • Enable power control with G-code “M2001”. (#47)

Bug Fixes

  • Fix: Turn off the laser when loss connection with Touchscreen. (#86)
  • Fix: Fix FreeRTOS delays. (#45)
  • Fix: Fix CNC Module spindle was not turned off if stop/finish working with Z distance from top is less than 30mm. (#51)

Improvement

  • Optimize start position behavior of 3D Printing Calibration. (#30)
  • Enable FPU for optimizing performance. (#48)
  • Reduce latency while all rodata are out of 256kB of Flash. (#60)

Module

Improvement

  • Enclosure light will blink once on power up to indicate works normally.
  • Optimize memory copy performance. (#3)

Touchscreen

New Features

  • Add module version detection when Touchscreen starts up.
  • Add Laser and CNC guide with the Rotary Module.
  • Add CNC Origin Assistant and Bit Assistant in Touchscreen.

Bug Fixes

  • Fix a bug where touchscreen crash when renaming folder in USB drive.

Improvements

  • Optimize file received via Wi-Fi.
  • Improve Touchscreen copywriting.
  • Improve UI of Control panel.

Downloads

Snapmaker2_V1.12.0

MD5: 0f5be08500651abce71d8c44a4d5ef70

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .
7 Likes

Apr 27 2021: Snapmaker2_V1.12.1

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

New Features

  • add “M413” G-code for enable/disable Power-Loss Recovery (#92)
    • Parameters
      • [S<enable>] S0/S1 for enable / disable Power-Loss Recovery
    • e.g. M413 S0 disable Power-Loss Recovery
  • add “M600” G-code for replace filament manually (#93)
    • You can add this G-code where you want to replace filament in .gcode file

Bug Fixes

  • Fix: Fix wrong value output with Enclosure lights and fan (#94)
  • Fix: Fix “M1006” G-code laser focus output with Snapmaker Luban (#95)
  • Fix: Fix X/Y coordinate of the first point in 3DP Calibration (#96)
  • Fix: Fix serial output messages in enclosure closing panel (#103)

Touchscreen

Improvement

  • Optimize copywriting in Origin Assistant

Downloads

Snapmaker2_V1.12.1

MD5: 3a2486f8eabf381b3bf4f1233fcd4289

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .
4 Likes

Jul 9 2021: Snapmaker2_V1.12.2

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

New Features

  • Support “M301” G-code for setting up Hotend PID.
    • Parameters
      • [P<Value>] [I<Value>] [D<Value>] for setting up Hotend PID

Bug Fixes

  • Fix a bug where bed mesh used in calibration didn’t match one used in printing.

Improvment

  • Improve the serial message id showing on while controller booting-up.

Downloads

Snapmaker2_V1.12.2

MD5: f71c8b85730e0e92b5ebae090c5e4c2c

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .
3 Likes

Jul 21 2021: Snapmaker2_V1.13.1

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

New Features

  • Add support for the Air Purifier.

Module

Bug Fixes

  • Fix a bug where 3D Printing Module heat up error with wrong PID.

Improvement

  • Improve Enclosure light output on power up.

Touchscreen

New Features

  • Add support for the Air Purifier.
    • Add Auto Turn On and Auto Turn Off options for Air Purifier.
  • Add German and French.
    • You can change the language settings through Settings > Language > language applicable > Save .

Bug Fixes

  • Fix a bug where Wi-Fi configuration won’t enabled on Touchscreen power up.

Improvement

  • Optimize UI/UX for Manual Focus using Laser Module.
  • Improve software crash report on Touchscreen.
    • You can check the anonymous data sharing option through Settings > User Preferences
  • Improve UI/UX for Print Settings Page
    • Optimize gesture actions for bottom tabs and swipe in/out logic.

Downloads

Snapmaker2_V1.13.1

MD5: f6a17d5ee9500c2d89dd803f24f716d2

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .
1 Like

Sep 13 2021: Snapmaker2_V1.13.2

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

New Features

  • Add “M425” G-code for saving backlash parameters. (#126)
  • Add remap 8-pin port feature for any axis. (#131)
  • Support G-code execution result triage. (#139)

Bug Fixes

  • Fix a bug where home_offset will set to 0 when using “M501” G-code.(#133)

  • Fix type of 3dp nozzle temperature. (#134)

  • Fixed a bug where power loss data could not be saved circulatively.(#138)

Touchscreen

New Features

  • Add Heated-Leveling feature for 3D Printing Module.
  • Return G-code responses in console when Wi-Fi remote connected via Snapmaker Luban.
    • Not all of the G-code responses were compatible for now. We will keep improving this feature in furture updates, please stay tune.
  • Add Enclosure light auto turn on upon startup options.
    • The option will be set as “Auto On” after upgrading from the previous version.

Bug Fixes

  • Fix a bug where showing wrong connected access point when back from password page in Wi-Fi settings.

Improvement

  • Optimize UI/UX for USB device detection.
  • Improve Wi-Fi connection experience.
    • Wi-Fi page will show up connection result while connecting.

Downloads

Snapmaker2_V1.13.2

MD5: 52ef37ce21f141077297ef0a48c4586f

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .
5 Likes

Dec 13 2021: Snapmaker2_V1.14.1

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Module

New Features

  • Support 10W High Power Laser Module
  • Add minimum version requirements for each modules.

Controller

New Features

  • Refactor G-code transmission for Printing.
  • Support 10W High Power Laser Module.
  • Add “M76” G-code for triggering pause request in printing.
  • Add “M1012” G-code for Emergency Stop Button status output.
  • Prohibit machine moving while controller could not recognized machine model.

Bug Fixes

  • Fix a bug where home_offset could not overrode in some case.
  • Fix a bug where “M92” G-code could not saved parameters.

Improvement

  • Optimize printing time consuming in Laser Engraving.
  • Optimize “M92” G-code output in console.
  • Improve sstp protocol for Touchscreen.
  • Optimize config file read/write logic for safety recovery.

Touchscreen

New Features

  • Support 10W High Power Laser Module.
  • Refactor G-code transmission for Printing.

Bug Fixes

  • Fix a bug where Wi-Fi status won’t updated when enabled/disabled Wi-Fi in Settings > Wi-Fi.

Improvement

  • Optimize 3D Printing Calibration
    • Touchscreen will pop up confirm dialog while machine was not calibrated successfully.
  • Improve touchscreen recovery from application crash.
  • Improve UX for unplug USB drive.
  • Update German and French copywriting.
  • Update resources for Settings > About Machine.

Downloads

Snapmaker2_V1.14.1

MD5: 2511404378127c07f2138838fa70a9df

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .
2 Likes

Jan 14 2022: Snapmaker2_V1.14.2

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

New Features

  • Add “M25” G-code for Pause Print command.

Bug Fixes

  • Fix a bug where 10W High Power Laser Module will not activate laser in some cases.
  • Fix a bug where Linear Module initialized wrong lead value while recovering from factory reset.

Improvement

  • Optimized print G-code transmission in printing.

Touchscreen

Bug Fixes

  • Fix a bug where Laser would not turn off while exiting Set Origin screen with 10W High Power Laser Module.
  • Fix a bug where Camera Capture will failed while Snapmaker Luban start capturing photo from machine in some cases.

Improvement

  • Optimized UX for Thickness Measurement Calibration.

Downloads

Snapmaker2_V1.14.2

MD5: ffd8c58ff73241b03fd9d84d9a24bbdb

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Jun 20 2022: Snapmaker2_V1.14.3

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

Improvement

  • Optimize “M1005” G-code output in console .

Touchscreen

New Features

  • Add Polish and Spanish .
    • You can change the language settings through Settings > Language > language applicable > Save .

Improvement

  • Optimize copywriting for Add-ons .
  • Update Model description in Settings > About Machine .

Downloads

Snapmaker2_V1.14.3

MD5: 563bd5a63d9b85c1cd92f3b16d88e6f7

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Jan 31 2023: Snapmaker2_V1.15.12

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Notice : Please update the latest version firmware before using Dual Extrusion 3D Printing Module.

Module

New Features

  • Support Dual Extrusion 3D Printing Module

Controller

New Features

  • Support Dual Extrusion 3D Printing Module

Bug Fixes

  • Fixed a bug that controller will not initializing unrecognized module to prevent firmware halted

Touchscreen

New Features

  • Support Dual Extrusion 3D Printing Module
    • added XY Offset Calibration, Sensor Calibration and Offset Calibration Check
    • added Flow Rate Control in printing

Bug Fixes

  • Fixed a bug that Touchscreen stuck in the blank screen after firmware downgraded

Improvement

  • 10W High Power Laser Module compatibility for Snapmaker 2.0 A150 model

Downloads

Snapmaker2_V1.15.12

MD5: d30c01ce86558ebcdd165316fdc8bdd3

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Feb 3 2023: Snapmaker2_V1.15.13

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

Improvement

  • Improved Linear Module exception interception

Touchscreen

Bug Fixes

  • Fixed a bug that pre-heated temperature not applied in Control
  • Fixed a bug that skip option will back to intro screen in Dual Extrusion Module Guide

Downloads

Snapmaker2_V1.15.13

MD5: 2beb0c78e93750a5ecfdfe7e6e38d495

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Feb 11 2023: Snapmaker2_V1.15.15

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

This is a beta version for Snapmaker 2.0 Firmware

Known issues: In nozzle temperature adjustment in printing with Dual Extrusion 3D Printing Module, the widget will point at zero when entered

Controller

Bug Fixes

  • Fixed a bug that live Z offset calculated incorrectly when go printing immediately after leveling

Touchscreen

Bug Fixes

  • Fixed a bug that the heated inactive extruder did not cool down when exiting the control page

Downloads

Snapmaker2_V1.15.15

MD5: 4fb26c1fb29963d732f59c971750ea0e

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Feb 17 2023: Snapmaker2_V1.15.17

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

Bug Fixes

  • Fixed a bug that live Z offset calculated incorrectly when go printing immediately after leveling

Touchscreen

Bug Fixes

  • Fixed a bug that the nozzle temperature adjust widget will point at the first time when printing
  • Fixed a bug that Touchscreen showed wrong add-on status while Dual Extrusion 3D Printing Module plugged
  • Fixed a bug that pre-heated option didn’t show up when switching to nozzle page when using Dual Extrusion 3D Printing Module

Downloads

Snapmaker2_V1.15.17

MD5: f0879e2a10103cadc9c575b376ea7584

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Feb 24 2023: Snapmaker2_V1.15.19

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

Bug Fixes

  • Fixed firmware watchdog to prevent firmware unexpected halt on boot
  • Fixed a bug that Sensor Calibration could not start when firmware parameters are lost in some scenario

Improvement

  • Improved valid value check of nozzle temperature in 3D Printing
  • Improved exception error report in Dual Extrusion 3D Printing Module

Touchscreen

Bug Fixes

  • Fixed a bug that overrides the right nozzle temperature during printing causes unexpected target temperature

Improvement

  • Improved exception error report in Dual Extrusion 3D Printing Module

Downloads

Snapmaker2_V1.15.19

MD5: 8c0051f0340b7c42fd82ae0a24ba2302

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Mar 6 2023: Snapmaker2_V1.15.20

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

Bug Fixes

  • Fixed a bug that Laser Camera Capture result shifted when using Snapmaker 2.0 A350 model

Improvement

  • Improved Dual Extrusion 3D Printing module initialization information data received to prevent not getting the right extruder offset value

Downloads

Snapmaker2_V1.15.20

MD5: c419b736f2820c180bae9e771b256467

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Mar 10 2023: Snapmaker2_V1.15.21

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Controller

Bug Fixes

  • Fixed a bug that hotend fan had stopped unexpectedly in some scenario

Touchscreen

Bug Fixes

  • Fixed minor wrong description in Dual Extrusion 3D Printing Module Feature.

Downloads

Snapmaker2_V1.15.21

MD5: 90a170500f4d8431c0607a00261fa492

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin .
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update .
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now .

Mar 29 2023: Snapmaker2_V1.15.22

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Touchscreen

New Features

  • Added display of Wi-Fi AP information
    • In Settings > Wi-Fi, connected AP networks will have an info icon, which when clicked, will display current network information

Bug Fixes

  • Fixed the issue where the screen disconnects immediately during remote connection in certain scenarios

Downloads

Snapmaker2_V1.15.22

MD5: c31a18d4bbaff6c6713c527edecbfde7

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin.
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update.
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now.

Apr 4 2023: Snapmaker2_V1.15.23

Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.

Changelog

Touchscreen

New Features

  • Added RSSI value display (signal sensitivity) in Wi-Fi network information

Downloads

Snapmaker2_V1.15.23

MD5: 0d4210f6071326260271f7d468fb2989

Notes

This firmware update is only compatible with Snapmaker 2.0.

To see your current firmware version, go to Settings > About Machine .

How to Update Firmware

  • Via a USB flash drive
    • Put the firmware update file Snapmaker2_V{version}.bin in your USB flash drive.
    • Plug the drive into the Controller.
    • On the Touchscreen, tap Files > USB > Snapmaker2_V{version}.bin.
  • Via Wi-Fi
    • On the Touchscreen, tap Settings > Firmware Update.
    • Read the changelog and download the firmware.
    • After the firmware is downloaded, tap Update Now.
1 Like