Has anyone had issues with the X-axis arm when printing is done? Whenever a print completes the X-axis goes to “0” and the Z-axis goes about halfway, then the Y-axis goes to “125” then “0” and hitting the X-axis arm along the way. It has knocked off most of my larger prints and has gone as bend the …

Hi Pineduhh, yes, I guess the same happened to me. [image] Reset run killed my print at the end Snapmaker Original Hi there, I printed thing:919475 (Millenium Falcon, thingieverse) yesterday. First part took 14h and it looked gorgeos! But at the end the head and the b…

Post your gcode which is knocked off here. I think this is a Slicer issue. @parachvte

[image] xchrisd: I think this is a Slicer issue. It’s probably something wrong with your “End G-code”, the Z goes down to make X hit with the print. BTW, did the Z axis drop down after the X and Z moves?

Hi Xchrisd, I cannot upload my complete gcode file. It says: “Sorry, that file is too big (maximum size is 4096kb).” (its 28 MB because it is a big model). Should I then only upload the last 4kB of it? Or you can just use the thingieverse STL of https://www.thingiverse.com/thing:919475 - I slice…

Hey @sven please upload it to a oneclickhoster, to your google-drive or dropbox. Or even the last 100lines of the code would do the same :wink:

yes kind of, the end of print calibration situation!

hey xchrisd, these are the roughly last 100 lines of my gcode: G0 X69.749 Y50.355 Z123.45 ;TYPE:WALL-OUTER G1 F1500 E2309.56109 G1 F1392.9 X69.981 Y50.55 E2309.56865 G1 X66.5 Y54.699 E2309.70375 G1 X66.372 Y54.852 E2309.70873 G1 X66.219 Y54.724 E2309.71194 G1 X65.987 Y54.528 E2309.71952 G1 X69.469 …

Your gcode is clear, no problem so far. From the video, it seems it´s gonna homing after falling down. May you try drive to Z100 instead of Z125 at your endgcode, maybe it drops there not. You could also delete your doubled gcodes, maybe there is the issue… M140 S0 ; BED OFF M107 ; FAN OFF ;En…

thanks for reviewing and checking! It knocks the model over in the end when homing the bed backwards. Then the x-axxis is too low. I would love to stop the “bed homing” in the end completly - is that also possible? BED OFF seems to stop only heating not moving. And is there a way to simulate th…

Taller Builds knocked off by X-axis arm

Original (3-in-1)

Pineduhh April 13, 2020, 4:24pm 7

Hey all,

Here is a link to the video of the issue. @sven is this similar to what you faced?
Video

After installing the z-axis extension. At the end of the output, the z-axis descends and spoils the output

Topic		Replies	Views
Reset run killed my print at the end Original (3-in-1)	1	517	April 13, 2020
After installing the z-axis extension. At the end of the output, the z-axis descends and spoils the output Original (3-in-1)	6	712	July 30, 2020
Z-Axis falling down? Original (3-in-1)	42	9936	January 2, 2020
Z offset Issue after Crash and not able to Print anymore Snapmaker 2.0 (3-in-1)	122	4295	December 4, 2021
Snapmaker 2.0 A350 Halting Mid-Print Snapmaker 2.0 (3-in-1)	1	349	September 7, 2021

Taller Builds knocked off by X-axis arm

Related topics