Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
New Features
Support “M301” G-code for setting up Hotend PID.
Parameters
[P<Value>] [I<Value>] [D<Value>] for setting up Hotend PID
Bug Fixes
Fix a bug where bed mesh used in calibration didn’t match one used in printing.
Improvment
Improve the serial message id showing on while controller booting-up.
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
New Features
Add support for the Air Purifier.
Module
Bug Fixes
Fix a bug where 3D Printing Module heat up error with wrong PID.
Improvement
Improve Enclosure light output on power up.
Touchscreen
New Features
Add support for the Air Purifier.
Add Auto Turn On and Auto Turn Off options for Air Purifier.
Add German and French.
You can change the language settings through Settings > Language > language applicable > Save .
Bug Fixes
Fix a bug where Wi-Fi configuration won’t enabled on Touchscreen power up.
Improvement
Optimize UI/UX for Manual Focus using Laser Module.
Improve software crash report on Touchscreen.
You can check the anonymous data sharing option through Settings > User Preferences
Improve UI/UX for Print Settings Page
Optimize gesture actions for bottom tabs and swipe in/out logic.
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
New Features
Add “M425” G-code for saving backlash parameters. (#126)
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Module
New Features
Support 10W High Power Laser Module
Add minimum version requirements for each modules.
Controller
New Features
Refactor G-code transmission for Printing.
Support 10W High Power Laser Module.
Add “M76” G-code for triggering pause request in printing.
Add “M1012” G-code for Emergency Stop Button status output.
Prohibit machine moving while controller could not recognized machine model.
Bug Fixes
Fix a bug where home_offset could not overrode in some case.
Fix a bug where “M92” G-code could not saved parameters.
Improvement
Optimize printing time consuming in Laser Engraving.
Optimize “M92” G-code output in console.
Improve sstp protocol for Touchscreen.
Optimize config file read/write logic for safety recovery.
Touchscreen
New Features
Support 10W High Power Laser Module.
Refactor G-code transmission for Printing.
Bug Fixes
Fix a bug where Wi-Fi status won’t updated when enabled/disabled Wi-Fi in Settings > Wi-Fi.
Improvement
Optimize 3D Printing Calibration
Touchscreen will pop up confirm dialog while machine was not calibrated successfully.
Improve touchscreen recovery from application crash.
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
New Features
Add “M25” G-code for Pause Print command.
Bug Fixes
Fix a bug where 10W High Power Laser Module will not activate laser in some cases.
Fix a bug where Linear Module initialized wrong lead value while recovering from factory reset.
Improvement
Optimized print G-code transmission in printing.
Touchscreen
Bug Fixes
Fix a bug where Laser would not turn off while exiting Set Origin screen with 10W High Power Laser Module.
Fix a bug where Camera Capture will failed while Snapmaker Luban start capturing photo from machine in some cases.
Improvement
Optimized UX for Thickness Measurement Calibration.
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
Improvement
Optimize “M1005” G-code output in console .
Touchscreen
New Features
Add Polish and Spanish .
You can change the language settings through Settings > Language > language applicable > Save .
Improvement
Optimize copywriting for Add-ons .
Update Model description in Settings > About Machine .
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Notice : Please update the latest version firmware before using Dual Extrusion 3D Printing Module.
Module
New Features
Support Dual Extrusion 3D Printing Module
Controller
New Features
Support Dual Extrusion 3D Printing Module
Bug Fixes
Fixed a bug that controller will not initializing unrecognized module to prevent firmware halted
Touchscreen
New Features
Support Dual Extrusion 3D Printing Module
added XY Offset Calibration, Sensor Calibration and Offset Calibration Check
added Flow Rate Control in printing
Bug Fixes
Fixed a bug that Touchscreen stuck in the blank screen after firmware downgraded
Improvement
10W High Power Laser Module compatibility for Snapmaker 2.0 A150 model
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
Improvement
Improved Linear Module exception interception
Touchscreen
Bug Fixes
Fixed a bug that pre-heated temperature not applied in Control
Fixed a bug that skip option will back to intro screen in Dual Extrusion Module Guide
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
This is a beta version for Snapmaker 2.0 Firmware
Known issues: In nozzle temperature adjustment in printing with Dual Extrusion 3D Printing Module, the widget will point at zero when entered
Controller
Bug Fixes
Fixed a bug that live Z offset calculated incorrectly when go printing immediately after leveling
Touchscreen
Bug Fixes
Fixed a bug that the heated inactive extruder did not cool down when exiting the control page
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
Bug Fixes
Fixed a bug that live Z offset calculated incorrectly when go printing immediately after leveling
Touchscreen
Bug Fixes
Fixed a bug that the nozzle temperature adjust widget will point at the first time when printing
Fixed a bug that Touchscreen showed wrong add-on status while Dual Extrusion 3D Printing Module plugged
Fixed a bug that pre-heated option didn’t show up when switching to nozzle page when using Dual Extrusion 3D Printing Module
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
Bug Fixes
Fixed firmware watchdog to prevent firmware unexpected halt on boot
Fixed a bug that Sensor Calibration could not start when firmware parameters are lost in some scenario
Improvement
Improved valid value check of nozzle temperature in 3D Printing
Improved exception error report in Dual Extrusion 3D Printing Module
Touchscreen
Bug Fixes
Fixed a bug that overrides the right nozzle temperature during printing causes unexpected target temperature
Improvement
Improved exception error report in Dual Extrusion 3D Printing Module
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
Bug Fixes
Fixed a bug that Laser Camera Capture result shifted when using Snapmaker 2.0 A350 model
Improvement
Improved Dual Extrusion 3D Printing module initialization information data received to prevent not getting the right extruder offset value
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Controller
Bug Fixes
Fixed a bug that hotend fan had stopped unexpectedly in some scenario
Touchscreen
Bug Fixes
Fixed minor wrong description in Dual Extrusion 3D Printing Module Feature.
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Touchscreen
New Features
Added display of Wi-Fi AP information
In Settings > Wi-Fi, connected AP networks will have an info icon, which when clicked, will display current network information
Bug Fixes
Fixed the issue where the screen disconnects immediately during remote connection in certain scenarios
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Touchscreen
New Features
Added RSSI value display (signal sensitivity) in Wi-Fi network information
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Touchscreen
New Features
Added retraction warning if G-code retraction distance was not recommended in Dual Extrusion 3D Printing Module
Bug Fixes
Fixed a bug that adjusting the Initial Layer nozzle temperature and heated bed temperature failed in 3D Printing
Controller
New Features
Added “C” and “W” custom parameter support with “M109” G-code
Improvement
Reduced retraction distance when pausing in 3D Printing job
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Touchscreen
New Features
Added Quick Swap Kit support
Improvements
Improved remaining storage checks when choosing a file in Touchscreen
Improved initial temperature parsing and applying logic in Touchscreen
Controller
New Features
Added Quick Swap Kit support
Bug Fixes
Fixed a bug that the 3D Printing tool head cooling fan was unexpectedly off when recovering from power loss
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Touchscreen
Bug Fixes
Fixed a bug that Luban couldn’t switch extruder when was connected to Touchscreen
Fixed a bug that G-code paramenters were replaced when parsing G-code file.
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Touchscreen
New Features
Added 20W Laser Module and 40W Laser Module support
Mainboard
New Features
Added 20W Laser Module and 40W Laser Module support
Module
New Features
Added 20W Laser Module and 40W Laser Module support
Thank you for your suggestions on how to make the Snapmaker 2.0 better. Your feedback is always appreciated. Here comes the latest version of the Snapmaker 2.0 firmware.
Changelog
Touchscreen
New Features
Refactor Touchscreen Print Job Management
In the previous version, when disconnected from Snapmaker Luban during print job, Touchscreen will request stop print job, and could not control the print job until reconnected from Luban.
In this version, when disconnected from Snapmaker Luban, Touchscreen will return to print. Print job control, power loss recovery and filament detection will recover on Touchscreen.
Added new Run Boundary Mode for 20W/40W Laser Module
Crosshairs Mode and Working Laser Mode
Bug Fixes
Fixed a bug that Touchscreen could not adjusted temperature and load filament when filament ran out during print
Fixed a bug that guide procedure did not finished correctly when using 10W Laser Module and Rotary Module
Fixed a bug that Touchscreen could not adjusted B Axis origin when using 20W/40W Laser Module and Rotary Module
Fixed a bug that Touchscreen showed wrong elapsed time in some scenario
Improvements
Improved Touchscreen UI/UX with Dual Extrusion 3D Printing Module and Quick Swap Kit
Optimized Toucreen processing for file transfer and upgrade when local storage is low
Notice: When local storage is low or insufficient, Touchscreen will clean up local files for free up enough space (according to the file created time locally, from earliest to latest).
Mainboard
New Features
M3/M4 Gcode update
Support for M3/M4 to turn Trapizoid Power on or off (in Marlin definition). This differs from standard Marlin, which configures LASER_POWER_TRAP when compiling firmware. The M3/M4 definition will now favor grbl.
Marlin’s M3 I and M4 I switching between Continuous Inline Mode and Dynamic Inline Mode is currently not supported. It is important to note that Marlin’s definition of Dynamic Inline Mode is not the same as Grbl’s definition of Dynamic Laser Power Mode.
G0/G1 Gcode update
In both M3 and M4, the laser is turned off when using the G0 movement.
Both Marlin and GRBL types of Inline Mode.
Module
Bug Fixes
Fixed a bug that flame sensor triggered on boot up unexpectedly in 20W/40W Laser Module