Well, almost perfect. It is within plus or minus .02mm or .0008". I’ve posted it to Thingiverse: [image] Indicator Mount by tonejaco This is a Dial Indicator mount for the side of the Snapmaker 2 print head. It can be used to check your bed level. A link to the Dial Indicator I got is i…

Tony’s spreadsheets are a wrapper that helps generate the syntax for the M421 command. Where the data comes from is not terribly important as long as the measurements you take are at the same place the firmware thinks it is. G42 can be used to move the head to mesh coordinates from 0…4 in I and J (…

One more question. I did a manual calibration a few minutes ago. I used the touch panel for going down 0.5 mm 4 times, then I used the jog in luban with a custom decrease of -0.01 mm. After finishing the calibration I started a print. I did not recognize that the printhead in the heating position wa…

During calibration, I think that’s the case? I can’t recall if I’ve tested that. However, 0.01mm difference is not enough to crash the nozzle, as it should’ve been at 0.1ish anyways, something else is at play here. It’s a good idea after a calibration to run the nozzle down to 5mm or so, and then …

Ok, finally I realized, that far too much for me. I was actually looking for something working like out of the box. I will try to keep this as simple as possible for me. Finally I did a manual leveling as good as I could. [IMG_3577] [M420V] Looking on that I would say mainly the right side and…

Is there a way of initiating the calibration sequence via the g-code console? or even just form Luban via usb?

Yes, see this topic. It’s not a single command, but many commands that the screen issues, all of which need to be run in order. [image] How to do a larger than 3 x 3 matrix level Snapmaker 2.0 So here’s my attempt at doing a leveling matrix larger than 3 x 3. Please be adv…

Anybody knows if I can just send an M421 command for the points that I like to change, or if it’s needed to send a command for all point (with Q.00)?

@FlyByWire , Hi, sorry for the delay, I’m out of town. Yes you can send individual M421 commands to change individual points thru the console in Luban with a USB connection. Remember that once you get to the place you want to be that you’ll need to save them with a M500 command. You don’t need to d…

For those who don’t have patience/skills - like me I found a workaround. What I did I found that corner/edge areas are farther from the nozzle and the extrusion is bad in those areas so marked them on the heating bed (more-less) . Than I took the plate off the bed and used the screws that hold t…

Do you have the platform mounted with the threaded inserts up, and that’s what you’re adjusting?

On achieving a perfect level

Snapmaker 2.0 (3-in-1)

brent113 October 9, 2020, 2:47am 197

Yes, see this topic. It’s not a single command, but many commands that the screen issues, all of which need to be run in order.

Topic		Replies	Views
SM2 Bed Leveling 101 Snapmaker 2.0 (3-in-1)	142	20317	January 25, 2023
On achieving a better leveling (With help from Snapmaker Devs) Snapmaker 2.0 (3-in-1)	41	5046	September 3, 2024
Leveling / First layer Problems Snapmaker2.0 Troubleshooting guides	39	3585	July 19, 2021
Bed Leveling - Revisited & Detailed Snapmaker 2.0 (3-in-1)	34	10016	July 29, 2024
Please help me with bed leveling first layer mess uneven Snapmaker 2.0 (3-in-1)	53	3766	January 7, 2023

On achieving a perfect level

Related topics