I posted my issue on Lightburn forum but it’s now becoming too much downtime. In the Lightburn console after every Move action it’s resetting position and coordinates. This means I cannot move the laser head to a position and mark/save it’s coordinates for repeat burns. I’ve tried setting the materi…

$S $Sta/SSID=GTAX11000 $Sta/Password=****** $Sta/IPMode=DHCP $Sta/IP=0.0.0.0 $Sta/Gateway=0.0.0.0 $Sta/Netmask=0.0.0.0 $AP/SSID=RAY2023 $AP/Password=****** $AP/IP=192.168.0.1 $AP/Channel=1 $System/Hostname=ray $Http/Enable=ON $Http/Port=80 $Telnet/Enable=ON $Telnet/Port=23 $Radio/Mode=STA $Message/E…

I have this problem too on 1.7.4 firmware 1.6.8 works properly [image] Snapmaker Ray Firmware Updates and Downloads Ray (Laser) We will release the latest Snapmaker Ray firmware updates and downloads under this topic. Your feedback is very much appreciated. Y…

Thanks for you response. I was using v1.7.2 with no issues before my laptop melted down. When I installed everything on the new PC I had this issue out of the gate. I learned they released a new firmware version the day after my issue was discovered. I guess it wouldn’t hurt to rollback the firmwar…

It would be really nice to get this fixed today. My IR module is being delivered today. I supposed I could use it on the SM2 or use the Ray with Luban. I’ve spent all my time and energy learning Lightburn so without it I feel like I’m working without arms.

[image] JohnSmith: I have this problem too on 1.7.4 firmware 1.6.8 works properly Snapmaker Ray Firmware Updates and Downloads You sir are fantastic. 1.6.8 does indeed work as expected. Looks like this is a Snapmaker firmware issue not Lightburn.

It would be really nice if some of the Snapmaker Team members could chime in. I now have reason to believe the new A>B feature that was introduced is the cause of the newer firmware resetting the coordinate position in Lightburn. I wonder if there’s a way they can add a toggle to switch between A>B…

With every move of the head in Lightburn the console says the position and coordinates are being reset because “disabling motor” expressed as: [I][PLAT]reset sys pos and WCO because disabling motor [I][PLAT]reset coordoffset So with the offset required to work with the ray (I’m talking about hav…

Here is an example of the offset inconsistencies between Luban and Lightburn Luban [Screenshot 2024-07-22 220740] Lightburn [Screenshot 2024-07-23 005455] Why are these two different and which one is actually correct? The numbers are so close and the crosshair lens is so large I cannot just me…

Here is a link to the rotary issue in my GroPro studio if anyone is interested to see what it’s doing. [image] Shared using GoPro Shared using GoPro

But why? "[I][PLAT]reset sys pos and WCO because disabling motor [I][PLAT]reset coordoffset"

Ray (Laser)

JohnSmith July 19, 2024, 11:46am 3

I have this problem too on 1.7.4
firmware 1.6.8 works properly

Topic		Replies	Views
Snapmaker Ray + Lightburn Ray (Laser)	13	1522	July 21, 2024
1064nm IR+20/40W + Lightburn Guide Snapmaker 2.0 (3-in-1)	125	7616	April 29, 2026
Full Lightburn Control Guide Snapmaker 2.0 (3-in-1)	549	40617	January 26, 2026
Many issues with new Snapmaker Ray Ray (Laser) Laser , 20w40w , Snapmaker_Luban	22	400	January 15, 2025
Snapmaker 2.0 A350T and Lightburn Snapmaker Luban	112	3430	November 3, 2023

But why? "[I][PLAT]reset sys pos and WCO because disabling motor [I][PLAT]reset coordoffset"

Related topics