Ok, at risk of making myself sound stupid. If i have model that is .2mm high on the z and my initial layer height is .2mm why does: a) the skirt print at .2mm high b) the model print at .4mm high doing this the model only has perimeters, solid infill and external perimeter I am using prusa iro…

ok an actual update. I fitted the used/tested/calibrated y rail from snapmaker to the left of my machine I fitted the old right y rail shown in this video on the right after I adjusted the bearing (remember the previous 2 rails was maybe 5 hours old from factory to replace my sloping rails). …

I don’t know if this helps because the colors aren’t in the photos but… [image] [image]

[image] brent113: Maybe pop the cap off the X axis and take a look. I have the two older replaced Y rails ‘for parts’ will undo one of them and look, lol. @Artezio that picture and that guide don’t mention which way to insert them - they assume one was looking lol. In fact that guide assum…

@scyto did you wait for support to tell you to open the rail?

@Artezio oh most definitely :slight_smile: they have all the details and are, i think, going to inspect two rails and then send them to me as known good to stop me claiming the rails are no good :wink: in the mean-time i am going to put the one rail back together with the good slider and raid one o…

@scyto ok phew lol. Woooo 4 new rails inside of a month, only 2 are good, partyyyyy

[image] Artezio: did you wait for support to tell you to open the rail? It’s not unreasonable to assume that the presence of the instructions on their public website condones following their procedure. There haven’t been any issues I’ve heard of resulting in people opening their rails on the…

@brent113 to use a horrible phrase ‘i don’t disagree’ but I have just learnt from other support interactions with other companies don’t open something until told to; then there is no risk of ‘you broke it, you pay for it’ - to be clear, I am super happy and impressed with snapmaker support. Nicole …

@brent113 true. I just saw people saying a while back that their warranty got denied because they opened a component without Snapmaker saying to. But it didn’t always cause them to deny a warranty, it was hit or miss and I think the mentality became “better safe than sorry” on its own lol. As for me…

[image] scyto: to use a horrible phrase ‘i don’t disagree’ but I have just learnt from other support interactions with other companies don’t open something until told to Of course that’s the most conservative thing to do. I have just noticed an increase in the quantity of posts and also ferv…

[image] scyto: Also having done this ‘procedure / instructions’ is very generous description of that page - seems more like ‘random facts’ and a ‘whole lot missing’ and possibly ‘some wrong’ What’s worse is it’s from the official distributor service manual. Not to mention the rusty part in th…

Why does an .2mm initial layer measure .4mm +?

Snapmaker 2.0 (3-in-1)

brent113 September 27, 2021, 6:42pm 53

Found my previous blurb:

Topic		Replies	Views
Cant get front to back Z alignment Snapmaker 2.0 (3-in-1)	26	2295	October 18, 2021
Please help me with bed leveling first layer mess uneven Snapmaker 2.0 (3-in-1)	53	3553	January 7, 2023
Fundamental Calibration Issue...? Snapmaker 2.0 (3-in-1)	80	3751	February 6, 2022
Can you really print the full bed capacity of an A350? Snapmaker 2.0 (3-in-1)	43	2117	October 22, 2021
Minimize rocking Snapmaker 2.0 (3-in-1)	91	5856	March 22, 2023

Why does an .2mm initial layer measure .4mm +?

Related topics