This thread is a continuous collection of user upgrades and mods. Category Top Panel Filament Loading Fan Camera Air Filter/Air Freshener Tool Holder Update We highly value the Upgrades and Mods shared by our community members, and we have compiled it into Wiki: Snapmaker J1/J1s Upgrades and Mods Community Resources | Snapmaker Wiki.

Top Panel Top Panel Riser - To make filament loading a lot easier and reduces the friction of the filament - Eric Manz [image] Top Panel Riser - To make filament loading a lot easier and reduces the friction of the filament - Peter Sgerm [image] Top Panel Riser - Add additional clearance for filament routing and an exhaust fan - Jeffrey Edgett [image] Top Panel Riser with Chamber Heater - Remix by Jeffrey Edgett and this version is designed for added chamber heater and many additional panels and pieces - James Bufkin [image] Top Panel Riser - Remix by benny911 and this version is designed for full raised panel with room for heat dissipation - Gav Bak [image] Top Panel holder - To hold the top panel - Bastian Loderhose [image]

Filament Loading PTFE Guide - To make filament loading easier and reduce the drag on the filament - Eric Manz [image] Filament Feedthrough - To put the spools inside the printer - Eric Manz [image] Magnetic Bowden Coupler - To make a simple transition from the original bowden tubes of the J1 to the more common 4mm ones - Eric Manz [image] Internal Spool Holder - To install the spools inside the printer - Eric Manz [image] Internal Spool Holder - Remix by Eric Manz and this version is designed for 8x12x3.5 bearings and made an adaptor ring - Søren Backmann [image] Magnetic Bowden Coupler - Remix by Eric Manz and this version is designed for magnets with a diameter of 6 mm and a thickness of 3 mm - Simone Bettini [image]

Fan Partcooling Fan Shroud - Fan Duct for the left and right extruder - Eric Manz [image] UFO Part Cooling Fan - An upgraded part cooling fan to improve printing - ChrisUFO [image]

Camera Camera Mount - To install a Raspberry Pi camera to machine and requires a raised lid - Eric Manz [image] Rear Raspberry Pi Mount - To install a Raspberry Pi on the machine without drilling new holes - Eric Manz [image] Beaglecam v2 camera mount - Structure for mounting Mintion Beagle V2 Camera in the front center of the enclosure frame - Simone Bettini [image]

Air Filter/Air Freshener Air Filter Purifier - To reduce the smells from printing by recirculating the air inside the printer - Eric Manz [image] ScentShield - A support for air fresheners to be installed inside the printer - Alberto Boz [image]

Tool Holder Tool Holder Set - To keep your tools and accessories for 3D printing - Jeffrey Edgett [image]

Can the Beaglecam v2 control the J1/J1S or are folks just using it to monitor prints? The A350T/A250T and F350T/F250T are listed as compatible. Thanks, Todd

Hi @tpearsall I saw one talented community member have posted the results of his experimentation a while back. You can monitor the printer (temperatures) and move ONE extruder (because it doesn’t support IDEX). Moving the Z seemed to be inverted and left the printer confused as to where Z was, and required a reset. You can learn more here: Snapmaker J1/J1s Owners | What happens when connecting the Beagle cam V2 to the rear port of the J1 | Facebook

Yet another lid riser. This is designed to be fully printable on the J1. No additional hardware is required in its most basic form, though there are optional interchangeable side panels for a hygrometer, feeding in a usb cable, or corners with magnets you place while printing. All the side panel options are the same dimensions so can be placed anywhere. I’ve not glued mine in case I ever decide to change one, but others have epoxied theirs together permanently. [image] Printable Snapmaker J1/J1s 40mm Riser by Wombley | Download free STL model |... A completely printable 40 mm lid riser/top hat for the Snapmaker J1 or J1s. | Download free 3D printable STL models Clever makers show it’s mirror symmetric for speedier printing, or also possible to fit a full set on one plate with the J1. I made it and didn’t notice. :sweat_smile: At 40mm height, it’s lower profile but still allows to relax the filament bend into the hotend to about 135 degrees instead of a hard 90 degrees.

Snapmaker J1/J1s Upgrades and Mods Resources

J1/J1s IDEX

Zoe February 19, 2024, 9:27am 4

Fan

Partcooling Fan Shroud - Fan Duct for the left and right extruder - Eric Manz

UFO Part Cooling Fan - An upgraded part cooling fan to improve printing - ChrisUFO

Topic		Replies	Views
Snapmaker J1/ --- Upgrades--- J1/J1s IDEX	38	4883	April 15, 2023
New Snapmaker J1, 1 month experience and review (cooler mod and speedbench run) J1/J1s IDEX Accessories , 3D_Models	13	1706	May 4, 2024
This device is really beta… J1/J1s IDEX	33	3310	May 4, 2023
Dont need to remove top of new J1s with cooling fans when printing with PLA! Is this TRUE? J1/J1s IDEX	12	1035	July 20, 2023
J1/J1s Wiki Updates J1/J1s IDEX	13	2855	August 20, 2024

Snapmaker J1/J1s Upgrades and Mods Resources

Fan

Related topics