I’m printing Inland PETG. It prints fine at 230C with a bed temperature of 75C. However I had to reduce the print speed to half of what I use for PLA.
I think the default print speed with the ABS setting is 40mm/s (PLA is the same, I think), which is fine for objects the size of which I can print with the Snapmaker. When I get a large format printer, then I’ll have to push the envelope on print speed to possibly shave days off a print.
I’m printing at 60mm/s for PLA. Sounds like I can get away with 40mm/s for PETG.
I think I’m going to have to slow the speed down below 40. Supports were having issues getting built tonight, as was infill.
I’m printing with PET-G since nearly half a year now. Not using PLA anymore.
Bed@65°C, nozzle@230-250°C (depends on the other settings and the filament) and 20 mm/s (for small items) up to 45 mm/s (for big items).
Stringing/oozing can occur at too high temperatures
I’ve always got crazy stringing haha
been trying to fix it for a while now
Yeah, small movements appear to be the bane of PETG. I have a print going right now at 30mm/s and there are four very small isolated supports that won’t stay put. Fortunately, they don’t appear to be critical (and I’m not even sure of their purpose), but with Snapmaker3D, there’s no option to remove them and there are places on the model that need supports. Two much larger support structures are printing fine.
What are the PRO’s of using PETG?
Similar properties to ABS and considerably less warp, so it’s easier to work with. It’s essentially soda bottle plastic.You can make things for your car using PETG or ABS; PLA will tend to melt down in a hot car.
Along with what @TheBum said, PETG is also slightly flexible and is classed as a flexible filament (if I am not mistaken). So, if printing something that needs to take a bit of a beating, PETG is amazing! I’ve printed some headset holders that require some flex with PETG.
Also it doesn’t absorb moisture from the air as much as PLA does, making it easier to store.
Here’s one half of the body of a rubber band gun done in purple eSun PETG. I had a tiny bit of lifting in one corner, but not bad at all. The rough areas are where the supports were; they came right off by hand. The white residue on the handle is glue that I haven’t washed off yet.
I’ve had less success with the silver eSun: it doesn’t want to bond very well. I may have to print it at a different temperature than the purple; I’ll print a temperature tower to figure out the best one…or I may end up tossing it.
My favorite PETG thus far is M3D’s ABS-R (R = “replacement”) which, despite its name, is based on PETG. It’s a proprietary blend that acts more like ABS when printing (including its extrusion temperature) but without nearly as much warping as ABS.
Despite this guide I’m having a really difficult time making detailed prints xD
Have you done a temperature tower and adjusted retraction? Have you tried a different brand of filament?
Haven’t tried a different brand of filament, but I’ve reduced the temp down to 190 C! It prints way better at this temp. Only issue I’ve had with the snapmaker is it doesn’t seem to be able to do small circles. I’ve tried changing the speed and all, but nothing has helped.
Small circles have been a problem with both of the printers I’ve used. There’s not much contact area for that short of a line of filament.
I read online that is may have to do with the constant heat that is around the general area. As the nozzle does not move too far away from the circle, the filament never has time to harden properly or settle, causing rough circles. I’m experimenting with simple towers that allow the nozzle to move away from the small radius for a brief few seconds.
Quick question. Do you have to do any physical modifications to the printer for this to work? Also is it flexible as pla flex?
No modifications needed. Don’t know PLA flex but PETG is similar to ABS but easier to handle.
Please have a look at following table:
It’s a long read but I found this very useful when tuning for PETG : http://forum.makergear.com/viewtopic.php?f=11&t=2593
Essentially you need to slow the printing speed down and increase retraction for best results.
Hi TheBum! One question about this tower.
How to send the instruction for temperature changing during the printing?
I would like to make a test, but i don’t know how to set a variable temperature…