# Snapmaker J1 Dual Drive Calibration

**URL:** <https://forum.snapmaker.com/t/snapmaker-j1-dual-drive-calibration/29750>\
**Category:** J1/J1s IDEX\
**Created:** [February 21, 2023, 8:05pm UTC](https://forum.snapmaker.com/t/snapmaker-j1-dual-drive-calibration/29750 "2023-02-21T20:05:37Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Legan](https://avatars.discourse-cdn.com/v4/letter/l/919ad9/32.png) [@Legan](https://forum.snapmaker.com/u/Legan)\
**Post date:** [February 21, 2023, 8:05pm UTC](https://forum.snapmaker.com/t/snapmaker-j1-dual-drive-calibration/29750/1 "2023-02-21T20:05:37Z")

</div>

Hello Community,  
i didnt found a way to check the extrusion of the dual gear.  
The Workspace in Luban did not recognizes my printer.  
I’m the only one who has the problem ?

---

<div class="post-metadata">

**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\
**Post date:** [February 21, 2023, 8:11pm UTC](https://forum.snapmaker.com/t/snapmaker-j1-dual-drive-calibration/29750/2 "2023-02-21T20:11:44Z")

</div>

Luban Version?  
Did you try a different one?

---

<div class="post-metadata">

**Author:** ![Legan](https://avatars.discourse-cdn.com/v4/letter/l/919ad9/32.png) [@Legan](https://forum.snapmaker.com/u/Legan)\
**Post date:** [February 21, 2023, 8:21pm UTC](https://forum.snapmaker.com/t/snapmaker-j1-dual-drive-calibration/29750/3 "2023-02-21T20:21:43Z")

</div>

I use 4.6.1 . I also tried the previous version

---

<div class="post-metadata">

**Author:** ![Legan](https://avatars.discourse-cdn.com/v4/letter/l/919ad9/32.png) [@Legan](https://forum.snapmaker.com/u/Legan)\
**Post date:** [February 21, 2023, 8:34pm UTC](https://forum.snapmaker.com/t/snapmaker-j1-dual-drive-calibration/29750/4 "2023-02-21T20:34:54Z")

</div>

Inconsistent Maschine Model  
The configured Maschine Model (Snapmaker J1 Idex does not match with the connected maschine (Artisan). To change the setting you can go to Maschine settings.

In the Maschine setting i can choose the J1 and save. After reconnect the message comes again and a windwos open where i can change a printer. In this Windwos the J1 does not exist.  
i connected the printer with usb

---

<div class="post-metadata">

**Author:** ![Legan](https://avatars.discourse-cdn.com/v4/letter/l/919ad9/32.png) [@Legan](https://forum.snapmaker.com/u/Legan)\
**Post date:** [February 21, 2023, 8:51pm UTC](https://forum.snapmaker.com/t/snapmaker-j1-dual-drive-calibration/29750/5 "2023-02-21T20:51:39Z")

</div>

Now I test it with wlan and it works. But my printer often loses the connection. The repeater is only 3 meters away from it. And now i am connected and can only give him gcode files:D A console for both extruder would be nice.