# Snapmaker Firmware 1.8.0?

**URL:** <https://forum.snapmaker.com/t/snapmaker-firmware-1-8-0/23575>\
**Category:** Snapmaker 2.0 (3-in-1)\
**Created:** [January 15, 2022, 1:50am UTC](https://forum.snapmaker.com/t/snapmaker-firmware-1-8-0/23575 "2022-01-15T01:50:57Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![Dodias](https://avatars.discourse-cdn.com/v4/letter/d/ec9cab/32.png) [@Dodias](https://forum.snapmaker.com/u/Dodias)\
**Post date:** [January 15, 2022, 1:50am UTC](https://forum.snapmaker.com/t/snapmaker-firmware-1-8-0/23575/1 "2022-01-15T01:50:57Z")

</div>

![snapmaker firmware](https://us1.discourse-cdn.com/flex022/uploads/snapmaker/original/3X/8/b/8b811c918c4fc69ee6405d050e4610eb3ea6362c.png)

I just installed my new enclosure and I had a firmware warning when I powered up the machine. Everything seemed to work ok, just the pesky warning message when I power on the unit. I was running firmware version 1.14.1 that I downloaded just after Christmas. I thought is strange that the version jumped from 1.14 to 1.8 ? but I wanted everything to run properly so I downloaded and installed the new firmware. I went to run an auto bed level check and the machine ran the table all the way out and then kept going! The motors made a horrible grinding and popping noise and would not stop. I hit my emergency stop button, which I test weekly, and it did not function at all. I had to throw my tool rack out of the way to hit the power supply switch. I have triple checked everything I know to do, but cannot find out what went wrong. I will have a very angry phone call with customer service when they open Monday.

I am man enough to admit if I have done something wrong, if someone out in the community could explain what that may be??? I would not recommend downloading the 1.8 firmware at this time.

---

<div class="post-metadata">

**Author:** ![brent113](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/brent113/32/11114_2.png) [@brent113](https://forum.snapmaker.com/u/brent113)\
**Post date:** [January 15, 2022, 1:57am UTC](https://forum.snapmaker.com/t/snapmaker-firmware-1-8-0/23575/2 "2022-01-15T01:57:45Z")

</div>

> [@Snapmaker 2.0 Firmware Updates and Downloads](https://forum.snapmaker.com/t/snapmaker-2-0-firmware-updates-and-downloads/5443):
>
> We will release the latest Snapmaker 2.0 firmware updates and downloads under this topic. Your feedback is very much appreciated. You can report any bugs or make any suggestions in the [discussion thread.](https://forum.snapmaker.com/t/discussion-of-snapmaker-2-0-firmware-updates/5441) Snapmaker 2.0 Firmware Version List Latest Version: [Snapmaker2\_V1.18.1](https://s3-us-west-2.amazonaws.com/snapmaker.com/download/firmware/Snapmaker2_V1.18.1.bin)[History Version 30(Oct. 25, 2023): V1.18.0](https://s3-us-west-2.amazonaws.com/snapmaker.com/download/firmware/Snapmaker2_V1.18.0.bin)[History Version 29(Sept. 5, 2023): V1.17.7](https://s3-us-west-2.amazonaws.com/snapmaker.com/download/firmware/Snapmaker2_V1.17.17.bin)[History Version 28(Jul. 27, 2023): V1.16.7](https://s3-us-west-2.amazonaws.com/snapmaker.com/download/firmware/Snapmaker2_V1.16.7.bin)[History Version 27(Jul. 14, 2023): V1.16.5](https://s3-us-west-2.amazonaws.com/snapmaker.com/download/firmware/Snapmaker2_V1.16.5.bin)[History Version 26(May. 19, 2023): V1.15.26](https://s3-us-west-2.amazonaws.com/snapmaker.com/download/firmware/Snapmaker2_V1.15.26.bin) …

1.8 is almost 2 years old. No idea why they didn’t update that site.

---

<div class="post-metadata">

**Author:** ![Dodias](https://avatars.discourse-cdn.com/v4/letter/d/ec9cab/32.png) [@Dodias](https://forum.snapmaker.com/u/Dodias)\
**Post date:** [January 15, 2022, 2:03am UTC](https://forum.snapmaker.com/t/snapmaker-firmware-1-8-0/23575/3 "2022-01-15T02:03:38Z")

</div>

Yea, the site even says this is the newest firmware?? I don’t know what is up with that. I have found my copy of firmware 1.14 where everything was working. I will try to reinstall and see what happens. I didn’t look at the version before I updated, just took that it states it is the latest…then after the fun started, I looked at the numbers closer.

---

<div class="post-metadata">

**Author:** ![Alan](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/alan/32/3418_2.png) [@Alan](https://forum.snapmaker.com/u/Alan)\
**Post date:** [January 15, 2022, 2:15am UTC](https://forum.snapmaker.com/t/snapmaker-firmware-1-8-0/23575/4 "2022-01-15T02:15:01Z")

</div>

Hi Dodias,

The site seem to be fine from here, could you help us to confirm the issue still  
exist?

 ![image](https://us1.discourse-cdn.com/flex022/uploads/snapmaker/original/3X/7/0/7090ea50532fcbef8681fe9741d4f7a854dec933.png)

Snapmaker 2.0 downloads:  
[https://snapmaker.com/snapmaker-2/downloads](https://snapmaker.com/snapmaker-2/downloads)

---

<div class="post-metadata">

**Author:** ![Dodias](https://avatars.discourse-cdn.com/v4/letter/d/ec9cab/32.png) [@Dodias](https://forum.snapmaker.com/u/Dodias)\
**Post date:** [January 15, 2022, 2:21am UTC](https://forum.snapmaker.com/t/snapmaker-firmware-1-8-0/23575/5 "2022-01-15T02:21:08Z")

</div>

I did just that, just now. The site is now showing the correct information. I have no idea how that could happen, but I went back to tab where I downloaded it and it still looked like my original pic with the 1.8.0 download link on the side when I hover over it. I went back to the home page and navigated back to the download section and it was back to the correct version/links. Just my luck, the interwebs go crazy and crash my printer! I am putting the correct firmware back on now and I will see what will happen. I hope there is no permanent damage to the unit.

---

<div class="post-metadata">

**Author:** ![CNC-Maker](https://avatars.discourse-cdn.com/v4/letter/c/df788c/32.png) [@CNC-Maker](https://forum.snapmaker.com/u/CNC-Maker)\
**Post date:** [January 15, 2022, 5:57am UTC](https://forum.snapmaker.com/t/snapmaker-firmware-1-8-0/23575/6 "2022-01-15T05:57:47Z")

</div>

@Alan you might want to change the wording on that site, as it is worded in a confusing way, which is why @Dodias installed the wrong firmware. Instead of saying, “_Please read this [article](https://forum.snapmaker.com/t/upgrade-the-toolheads-separately-with-snapmaker-firwmare-v1-12-0/17402) before you upgrade the firmware to V1.12.0._”, you might want to say something like:

If you are upgrading from a version of firmware prior to v1.12.0, please follow the directions in the following article and use the latest version of firmware in place of v1.12.0 while following them:

> [@Upgrade the Toolheads Separately with Snapmaker Firmware V1.12.0](https://forum.snapmaker.com/t/upgrade-the-toolheads-separately-with-snapmaker-firmware-v1-12-0/17402):
>
> To use the Emergency Stop Button and the Rotary Module, you need to upgrade all modules to [Snapmaker Firmware V1.12.0](https://s3-us-west-2.amazonaws.com/snapmaker.com/download/firmware/Snapmaker2_V1.12.0.bin), the tool-heads included. With this version of Snapmaker firmware, the Touchscreen will ask you to upgrade three tool-heads with the USB flash drive. You will see the Touchscreen notification “Outdated firmware (Modules) detected. Please visit our website, download the latest version, and update before use.” Notice If you have used all tool-heads (3D printing module, laser eng…
