# Slicing destroys model

**URL:** <https://forum.snapmaker.com/t/slicing-destroys-model/15535>\
**Category:** Snapmaker Luban\
**Created:** [February 6, 2021, 8:38pm UTC](https://forum.snapmaker.com/t/slicing-destroys-model/15535 "2021-02-06T20:38:05Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![spec24](https://avatars.discourse-cdn.com/v4/letter/s/ac8455/32.png) [@spec24](https://forum.snapmaker.com/u/spec24)\
**Post date:** [February 6, 2021, 8:38pm UTC](https://forum.snapmaker.com/t/slicing-destroys-model/15535/1 "2021-02-06T20:38:05Z")

</div>

Ok, so I have a pretty simple model. No issues in Slic3r or on the Prusa. When I slice this, though, this is the result I get. I attempted to print but it turned out just like you see it here. None of the shaft was even joined. Totally hollow even though infill is 25%. Using Luban 3.13.1. Anyone have any idea what’s going on?

 ![image_2021-02-06_153732](https://us1.discourse-cdn.com/flex022/uploads/snapmaker/original/2X/6/679249978e3c96a55d66a3acbeb5b5d016dc27fa.png)  
 ![MODEL](https://us1.discourse-cdn.com/flex022/uploads/snapmaker/original/2X/7/71f60096ea31ffbd812190bae09920bcf88e89d4.jpeg)

---

<div class="post-metadata">

**Author:** ![sdj544](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/sdj544/32/11365_2.png) [@sdj544](https://forum.snapmaker.com/u/sdj544)\
**Post date:** [February 7, 2021, 4:02am UTC](https://forum.snapmaker.com/t/slicing-destroys-model/15535/4 "2021-02-07T04:02:37Z")

</div>

Are you positive the model is actually joined in the stl?  
Might want to check it in meshmixer or meshlab.  
I had one that I created and printed and when I went to pull it off the bed it pulled apart. When I went and checked it I realized that when I had positioned the two shapes together there was a .01mm gap. I couldn’t see it when I rotated it but when I printed it it printed as two separate pieces.  
-S

---

<div class="post-metadata">

**Author:** ![spec24](https://avatars.discourse-cdn.com/v4/letter/s/ac8455/32.png) [@spec24](https://forum.snapmaker.com/u/spec24)\
**Post date:** [February 7, 2021, 2:13pm UTC](https://forum.snapmaker.com/t/slicing-destroys-model/15535/5 "2021-02-07T14:13:27Z")

</div>

The model is 100% manifold. So, I haven’t had time to go through all the setting but these were the base settings that the Snapmaker vase model uses. When I swithed to “normal” print settings this issue went away. I’m not sure what settings would totally remove surfaces but at least I’ve gotten around it. Thanks!!

---

<div class="post-metadata">

**Author:** ![MooseJuice](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/moosejuice/32/10684_2.png) [@MooseJuice](https://forum.snapmaker.com/u/MooseJuice)\
**Post date:** [February 7, 2021, 2:44pm UTC](https://forum.snapmaker.com/t/slicing-destroys-model/15535/6 "2021-02-07T14:44:31Z")

</div>

luban sucks. use the prusaslicer instead if you are familiar with it. everyone moves past luban, its just for the first timers to play with.

---

<div class="post-metadata">

**Author:** ![clewis](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/clewis/32/3255_2.png) [@clewis](https://forum.snapmaker.com/u/clewis)\
**Post date:** [February 8, 2021, 7:15pm UTC](https://forum.snapmaker.com/t/slicing-destroys-model/15535/7 "2021-02-08T19:15:05Z")

</div>

In Luban and Cura, I like to run through the layers and print head movements to see if I can spot any problems ahead of time. I usually focus on the first layer and any places I suspect might need supports. I’ve caught a few errors by noticing that the print head makes a wall in places that I think it shouldn’t, like sdj544’s example of a part with a tiny gap in it.
