# Please share settings for good overhangs

**URL:** <https://forum.snapmaker.com/t/please-share-settings-for-good-overhangs/32521>\
**Category:** Snapmaker 2.0 (3-in-1)\
**Tags:** Gcode, 3D\_Models, Slicer\_Profile\
**Created:** [August 12, 2023, 2:36pm UTC](https://forum.snapmaker.com/t/please-share-settings-for-good-overhangs/32521 "2023-08-12T14:36:24Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Rob204](https://avatars.discourse-cdn.com/v4/letter/r/a698b9/32.png) [@Rob204](https://forum.snapmaker.com/u/Rob204)\
**Post date:** [August 12, 2023, 2:36pm UTC](https://forum.snapmaker.com/t/please-share-settings-for-good-overhangs/32521/1 "2023-08-12T14:36:24Z")

</div>

![IMG_20230812_162017_478](https://us1.discourse-cdn.com/flex022/uploads/snapmaker/original/3X/3/e/3e1f63555c32306a02fe0a09ad7532ddf3112e7a.jpeg)

I give up.  
I’ve used various recommendations from around the web to improve my overhangs, but it just doesn’t work.

Is there anyone of you who can print good overhangs at least up to 45 degrees and if so, please share his settings?

Best regards.

---

<div class="post-metadata">

**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\
**Post date:** [August 13, 2023, 7:18pm UTC](https://forum.snapmaker.com/t/please-share-settings-for-good-overhangs/32521/2 "2023-08-13T19:18:45Z")

</div>

You print too hot or your part cooler is too low.  
Improve your cooling or print temperature and see if it gets better.

Maybe this helps you for more understanding:

> [@Snapmaker Tower Tips! (Images included)](https://forum.snapmaker.com/t/snapmaker-tower-tips-images-included/2750):
>
> Hey all! If you’ve tried to make a small tower with the snapmaker, you;ve probably noticed the walls look terrible and it isn’t setting properly. [[Album] Imgur [Imgur] ](https://imgur.com/a/g70ysg0) Figure 1: It’s difficult to see, however, the print has unevent sides and caved in sections. What causes this? This is caused by the nozzle never having time to …

---

<div class="post-metadata">

**Author:** ![clewis](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/clewis/32/3255_2.png) [@clewis](https://forum.snapmaker.com/u/clewis)\
**Post date:** [August 14, 2023, 7:06pm UTC](https://forum.snapmaker.com/t/please-share-settings-for-good-overhangs/32521/3 "2023-08-14T19:06:49Z")

</div>

I find that a smaller layer height helps. I can print 50º at 0.2mm, and 60º at 0.1mm before it starts getting noodley.

---

<div class="post-metadata">

**Author:** ![Rob204](https://avatars.discourse-cdn.com/v4/letter/r/a698b9/32.png) [@Rob204](https://forum.snapmaker.com/u/Rob204)\
**Post date:** [August 14, 2023, 8:32pm UTC](https://forum.snapmaker.com/t/please-share-settings-for-good-overhangs/32521/4 "2023-08-14T20:32:41Z")

</div>

Thank you, I will check this.  
Best regards