# Orca slicer profile and/or full tech specs **URL:** \ **Category:** Original (3-in-1)\ **Created:** [August 25, 2024, 8:01pm UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823 "2024-08-25T20:01:18Z")\ **Posts on this page:** 8\ **Page:** 1
**Author:** ![Pieyrot](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/pieyrot/32/3752_2.png) [@Pieyrot](https://forum.snapmaker.com/u/Pieyrot)\ **Post date:** [August 25, 2024, 8:01pm UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823/1 "2024-08-25T20:01:18Z")
Hi, I’m configuring Orca slicer for my good old Snapmaker Original. But before reinventing the wheel, I was wondering if anybody had alread done it and got a profile? And if not, where can I find the full technical specs, like motor max acceleration and speed, etc. Thanks! ---
**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\ **Post date:** [August 26, 2024, 7:28am UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823/2 "2024-08-26T07:28:22Z")
If you read out the machine settings by entering M503 in the console, there are the acceleration and speed limits. ---
**Author:** ![Pieyrot](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/pieyrot/32/3752_2.png) [@Pieyrot](https://forum.snapmaker.com/u/Pieyrot)\ **Post date:** [August 26, 2024, 8:02pm UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823/3 "2024-08-26T20:02:47Z")
Awsome! thank you. You’re right, now that you tell me, that rings a bell… It’s always under your noze and you don’t see it 🙂 ---
**Author:** ![clewis](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/clewis/32/3255_2.png) [@clewis](https://forum.snapmaker.com/u/clewis)\ **Post date:** [August 30, 2024, 12:46am UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823/4 "2024-08-30T00:46:48Z")
Or you can just use Snapmaker’s build: [OrcaSlicer Nightly Builds for Snapmaker Community - Dev Version](https://forum.snapmaker.com/t/orcaslicer-nightly-builds-for-snapmaker-community-dev-version/36846/1) ---
**Author:** ![Pieyrot](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/pieyrot/32/3752_2.png) [@Pieyrot](https://forum.snapmaker.com/u/Pieyrot)\ **Post date:** [August 30, 2024, 6:19am UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823/5 "2024-08-30T06:19:32Z")
I already have V2.1.1. All new SnapMaker are there, but not the original… ---
**Author:** ![clewis](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/clewis/32/3255_2.png) [@clewis](https://forum.snapmaker.com/u/clewis)\ **Post date:** [August 30, 2024, 6:11pm UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823/6 "2024-08-30T18:11:28Z")
I forgot that I’m not the only Original user still out there. They also left us out of the [wiki](https://wiki.snapmaker.com/en/home). Can you use the A150, and reduce the build volume to 125mm in all dimensions? ---
**Author:** ![Pieyrot](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/pieyrot/32/3752_2.png) [@Pieyrot](https://forum.snapmaker.com/u/Pieyrot)\ **Post date:** [August 31, 2024, 3:12pm UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823/7 "2024-08-31T15:12:09Z")
> [@clewis](#): > > A150 Qould work… But does the A150 has the same tech specs that the Original? I doubt… if it’s a V2.0 it should be “better” than the V1… I’m now not missing much. only the max speed was not available in the M503 command… ---
**Author:** ![JustJoshinMagic](https://avatars.discourse-cdn.com/v4/letter/j/71c47a/32.png) [@JustJoshinMagic](https://forum.snapmaker.com/u/JustJoshinMagic)\ **Post date:** [September 17, 2024, 7:47pm UTC](https://forum.snapmaker.com/t/orca-slicer-profile-and-or-full-tech-specs/36823/8 "2024-09-17T19:47:57Z")
When you finish this, can you share it? I’ve been trying to find a profile for my Snapmaker original as well