# Linear module cables

**URL:** <https://forum.snapmaker.com/t/linear-module-cables/15972>\
**Category:** Showcase & Prints\
**Created:** [February 16, 2021, 4:22am UTC](https://forum.snapmaker.com/t/linear-module-cables/15972 "2021-02-16T04:22:18Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![chrome98](https://avatars.discourse-cdn.com/v4/letter/c/82dd89/32.png) [@chrome98](https://forum.snapmaker.com/u/chrome98)\
**Post date:** [February 16, 2021, 4:22am UTC](https://forum.snapmaker.com/t/linear-module-cables/15972/1 "2021-02-16T04:22:18Z")

</div>

What type of connector is used on the SM 2 linear module wires?

---

<div class="post-metadata">

**Author:** ![Artezio](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/artezio/32/15834_2.png) [@Artezio](https://forum.snapmaker.com/u/Artezio)\
**Post date:** [February 19, 2021, 11:41pm UTC](https://forum.snapmaker.com/t/linear-module-cables/15972/2 "2021-02-19T23:41:25Z")

</div>

It’s proprietary and only available from snapmaker, honestly I think they would’ve been better off going with established. Would make it much easier, I believe the polarity in their design is reversed vs established designs, could be wrong though

---

<div class="post-metadata">

**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\
**Post date:** [February 20, 2021, 9:35am UTC](https://forum.snapmaker.com/t/linear-module-cables/15972/3 "2021-02-20T09:35:11Z")

</div>

Here you go, the plugs a re clarified in the post and available at mouser.

> [@Custom Extension Module](https://forum.snapmaker.com/t/custom-extension-module/13424/5):
>
> a pair of solderd D-Subs later Testing them also didnt kill my Controller and the Analyser is able to read CANbus so im assuming they are “to spec” ? Pinouts of the Snapmaker cabels, only CAN and power are used in my Connectors, Step and such arent requierd for my usage so they are shrinked off. DB9 Connector Pinout: 2: CAN\_L 3: CAN\_GND 6: GND 7: CAN\_H 9: CAN\_PWR Pin 3 and Pin 6 are connected inside the D-Sub Connectors in my …

---

<div class="post-metadata">

**Author:** ![Streupfeffer](https://avatars.discourse-cdn.com/v4/letter/s/f9ae1b/32.png) [@Streupfeffer](https://forum.snapmaker.com/u/Streupfeffer)\
**Post date:** [February 20, 2021, 11:09am UTC](https://forum.snapmaker.com/t/linear-module-cables/15972/4 "2021-02-20T11:09:17Z")

</div>

The Connectors on teh SN itself are custom (or atleast i didnt find them sofar, maybe a more obscure supplier?) The D-Subs are standart stuff to buy. I got my Cables by asking Support for a couple, relativly cheap, iirc Shipping was the most expensive.