# Initial setup failed

**URL:** <https://forum.snapmaker.com/t/initial-setup-failed/10073>\
**Category:** Snapmaker2.0 Troubleshooting guides\
**Created:** [October 3, 2020, 5:36pm UTC](https://forum.snapmaker.com/t/initial-setup-failed/10073 "2020-10-03T17:36:43Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Loes57](https://avatars.discourse-cdn.com/v4/letter/l/f9ae1b/32.png) [@Loes57](https://forum.snapmaker.com/u/Loes57)\
**Post date:** [October 3, 2020, 5:36pm UTC](https://forum.snapmaker.com/t/initial-setup-failed/10073/1 "2020-10-03T17:36:43Z")

</div>

Hi, I just started the initial calibration process, but the print module misses points 1, 2, 3 it ends up further than the bed, as a result all the other poinst are wrong too. Is there a possibitlity to solve this? Thanks! Greetings from the Netherlands.

---

<div class="post-metadata">

**Author:** ![sdj544](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/sdj544/32/11365_2.png) [@sdj544](https://forum.snapmaker.com/u/sdj544)\
**Post date:** [October 3, 2020, 7:38pm UTC](https://forum.snapmaker.com/t/initial-setup-failed/10073/2 "2020-10-03T19:38:04Z")

</div>

Post pics.  
Make sure your y axis are properly lined up in the slots. (not too far forward or back)  
Also the sensor is not in the same place as the nozzle. It’s to the right.

-S

---

<div class="post-metadata">

**Author:** ![Loes57](https://avatars.discourse-cdn.com/v4/letter/l/f9ae1b/32.png) [@Loes57](https://forum.snapmaker.com/u/Loes57)\
**Post date:** [October 3, 2020, 9:58pm UTC](https://forum.snapmaker.com/t/initial-setup-failed/10073/3 "2020-10-03T21:58:37Z")

</div>

Hi S, thank you for your help, I’m feeling really dumb that I didn’t notice earlier that I made a mistake, you we’re so right. 😆 Now it’s better, but the nozzle is still slightly off centre. Can I change that? Thanks again! Loes

---

<div class="post-metadata">

**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\
**Post date:** [October 4, 2020, 11:32am UTC](https://forum.snapmaker.com/t/initial-setup-failed/10073/4 "2020-10-04T11:32:32Z")

</div>

> [@sdj544](#):
>
> the sensor is not in the same place as the nozzle. It’s to the right.

Hey @Loes57, as sdj544 wrote, the sensor is off the nozzle.- There is no need to change the center position of the nozzle, because you calibrate with the sensor.

---

<div class="post-metadata">

**Author:** ![Loes57](https://avatars.discourse-cdn.com/v4/letter/l/f9ae1b/32.png) [@Loes57](https://forum.snapmaker.com/u/Loes57)\
**Post date:** [October 4, 2020, 3:17pm UTC](https://forum.snapmaker.com/t/initial-setup-failed/10073/5 "2020-10-04T15:17:10Z")

</div>

Ok, many thanks, printing now and it seems to be alright! :-). Grtz, Loes
