# How do you handle sagging/bending PTFE tubes?

**URL:** <https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432>\
**Category:** U1 Toolchanger\
**Created:** [March 10, 2026, 11:10pm UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432 "2026-03-10T23:10:35Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![Cylonmode](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/cylonmode/32/30291_2.png) [@Cylonmode](https://forum.snapmaker.com/u/Cylonmode)\
**Post date:** [March 10, 2026, 11:10pm UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432/1 "2026-03-10T23:10:35Z")

</div>

So, the PTFE tubes on all my toolheads sag and bend pretty bad… Especially 3 and 4. Toolhead #3 gets dangerously close to obstructing toolhead #4.

What have others done to remedy this problem?

I have considered something like this, but curious if there are other solutions out there.

[https://makerworld.com/en/models/2162573-snapmaker-u1-ptef-tube-tensioner?from=search#profileId-2344708](https://makerworld.com/en/models/2162573-snapmaker-u1-ptef-tube-tensioner?from=search#profileId-2344708)

or something like this one:

[https://makerworld.com/en/models/2368330-snapmaker-u1-ptfe-tube-holder?from=search#profileId-2591942](https://makerworld.com/en/models/2368330-snapmaker-u1-ptfe-tube-holder?from=search#profileId-2591942)

---

<div class="post-metadata">

**Author:** ![fred\_dot\_u](https://avatars.discourse-cdn.com/v4/letter/f/f1d935/32.png) [@fred\_dot\_u](https://forum.snapmaker.com/u/fred_dot_u)\
**Post date:** [March 10, 2026, 11:32pm UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432/2 "2026-03-10T23:32:53Z")

</div>

Do you think that printing both items and putting them in use is practical?

---

<div class="post-metadata">

**Author:** ![Cylonmode](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/cylonmode/32/30291_2.png) [@Cylonmode](https://forum.snapmaker.com/u/Cylonmode)\
**Post date:** [March 11, 2026, 12:38am UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432/3 "2026-03-11T00:38:53Z")

</div>

I did, but worried the tensioner puts too much strain on the toolhead. I’m definitely going to try the second file (tube holder) and see if it does anything positive.

---

<div class="post-metadata">

**Author:** ![LutzHB](https://avatars.discourse-cdn.com/v4/letter/l/d26b3c/32.png) [@LutzHB](https://forum.snapmaker.com/u/LutzHB)\
**Post date:** [March 11, 2026, 10:39pm UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432/4 "2026-03-11T22:39:02Z")

</div>

I would definitely remove this additional orange cross-connection. In my assessment, it only placed additional strain on the overall system and offered no advantage.

I don’t understand how something could get blocked on your end. After all, only one head is active at a time and cannot overtake the other heads or become entangled with them.

I have secured everything on my end with the included clamps, and so far there has been no blockage or dangerous situation.

If the hoses or mounts become worn after a few years, they will simply be replaced. If they fail before a certain service life is reached, I would contact Snapmaker.

---

<div class="post-metadata">

**Author:** ![Cylonmode](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/cylonmode/32/30291_2.png) [@Cylonmode](https://forum.snapmaker.com/u/Cylonmode)\
**Post date:** [March 11, 2026, 11:45pm UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432/5 "2026-03-11T23:45:02Z")

</div>

> [@LutzHB](#):
>
> I would definitely remove this additional orange cross-connection. In my assessment, it only placed additional strain on the overall system and offered no advantage.

The cross section is the whole point of the model… Read the description.

But, I have no problems yet. Toolhead 1 and 2 sag to the left, Toolhead 3 and 4 sag to the right. Toolhead 3 sags to the right more than Toolhead 4 does, therefore it gets close. I don’t anticipate them ever really “tangling” but could cause increased friction or resistance.

---

<div class="post-metadata">

**Author:** ![CrazyIvan](https://avatars.discourse-cdn.com/v4/letter/c/7bcc69/32.png) [@CrazyIvan](https://forum.snapmaker.com/u/CrazyIvan)\
**Post date:** [March 12, 2026, 8:25am UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432/6 "2026-03-12T08:25:12Z")

</div>

I’m thinking something like a loose spring, just to stop the tube+cable sagging. OK, so that’s probably not something you can print, but…

---

<div class="post-metadata">

**Author:** ![Cylonmode](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/cylonmode/32/30291_2.png) [@Cylonmode](https://forum.snapmaker.com/u/Cylonmode)\
**Post date:** [March 12, 2026, 10:58am UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432/7 "2026-03-12T10:58:05Z")

</div>

The ptfe tube holder in the second file works pretty good, I’m not going to try the tensioner.

---

<div class="post-metadata">

**Author:** ![cdemaris](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/cdemaris/32/16589_2.png) [@cdemaris](https://forum.snapmaker.com/u/cdemaris)\
**Post date:** [March 13, 2026, 2:53pm UTC](https://forum.snapmaker.com/t/how-do-you-handle-sagging-bending-ptfe-tubes/41432/8 "2026-03-13T14:53:03Z")

</div>

A simple solution might be tape or twist ties. I have used twist ties to hold cables etc. in place and they are easy to remove.
