# Cura temperature not right
**URL:** https://forum.snapmaker.com/t/cura-temperature-not-right/33350
**Category:** Artisan (3-in-1)
**Created:** [October 25, 2023, 12:36pm UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350 "2023-10-25T12:36:15Z")
**Posts on this page:** 8
**Page:** 1
### Author:  [@joost03](https://forum.snapmaker.com/u/joost03)
#### Post date: [October 25, 2023, 12:36pm UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350/1 "2023-10-25T12:36:15Z")
I’m trying to print something with PETG and PVA support. I have the Snapmaker plugin in Cura and have PVA selected as my support I also selected the right nozzle as support I set the temperature for my left nozzle to 230 for PETG and my right nozzle to 215 for PVA but when I start the print the right nozzle goes to 230 which is way too hot for PVA. Does anyone know a solution?
---
### Author:  [@Savoie](https://forum.snapmaker.com/u/Savoie)
#### Post date: [October 26, 2023, 2:49pm UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350/2 "2023-10-26T14:49:05Z")
I have noticed the same problem. But it only occurs with the first layer. The temperature is correct for the other layers.
The problem does not always occur, I think it depends on which extruder was active before the job start.
You can set the temperature manually on the controller during printing to 215.
---
### Author:  [@clewis](https://forum.snapmaker.com/u/clewis)
#### Post date: [October 26, 2023, 3:46pm UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350/3 "2023-10-26T15:46:16Z")
Can you upload your GCode? If the GCode shows setting the heads correctly, that would be a bug report to Snapmaker.
---
### Author:  [@Savoie](https://forum.snapmaker.com/u/Savoie)
#### Post date: [November 11, 2023, 9:05am UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350/4 "2023-11-11T09:05:04Z")
Now i have the issue.
I print with the right extruder at 230°C. But it preheats to 240°C which is the left extruder temp.
Extruder Left:
Extruder Right
possible that the start gcode (variables) in cura only look at the temperature of the first extruder?
[Halter110.gcode](https://forum.snapmaker.com/uploads/short-url/5AJWp8TMQMKCJ2HV1pTnz6obf32.gcode) (876.1 KB)
---
### Author:  [@Rwide](https://forum.snapmaker.com/u/Rwide)
#### Post date: [November 11, 2023, 12:26pm UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350/5 "2023-11-11T12:26:51Z")
@Savoie I think if you change your build plate adhesion extruder, it should work…
---
### Author:  [@Savoie](https://forum.snapmaker.com/u/Savoie)
#### Post date: [January 15, 2024, 8:24pm UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350/6 "2024-01-15T20:24:53Z")
How can i do that?
At the moment i have the same problem again. I use Extruder 2 (Right) for my part.
Extruder 1 (Left) is empty and disabled in Cura.
Now when i start the print it heats the nozzle to the temperature of Extruder 1 and i got an error message “Filament Runout Sensor Left Extruder” - But Left is disabled in Cura 😵💫
---
### Author:  [@Rwide](https://forum.snapmaker.com/u/Rwide)
#### Post date: [January 15, 2024, 9:09pm UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350/7 "2024-01-15T21:09:51Z")
---
### Author:  [@Savoie](https://forum.snapmaker.com/u/Savoie)
#### Post date: [January 16, 2024, 6:27pm UTC](https://forum.snapmaker.com/t/cura-temperature-not-right/33350/8 "2024-01-16T18:27:54Z")
Thank you. Setting was hidden. Now its visible and it solved my problem.