# "Bump" in Y-axis **URL:** \ **Category:** Snapmaker 2.0 (3-in-1)\ **Created:** [October 2, 2020, 12:16pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017 "2020-10-02T12:16:27Z")\ **Posts on this page:** 20\ **Page:** 1
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 2, 2020, 12:16pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/1 "2020-10-02T12:16:27Z")
Hi, I finally received my Snapmaker A350 šŸ™‚ After setting it up i noticed that when i run the print calibration, there is a ā€œbumpā€ when the Y axis move. I can both hear and feel it if i put my finger on the base plate / linear module. The bump appear in the same area every time, on the last third of the axis movement. When I turn the machine off and move the axis by hand, it moves completely smooth without any bumps. Anyone got an idea why this bump appear / how to fix? ---
**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\ **Post date:** [October 2, 2020, 6:39pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/2 "2020-10-02T18:39:12Z")
Make a video about would help. Disassemble the bed and the piece under the bed to let the axis drive freely to see from which module the issue comes. ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 3, 2020, 9:08am UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/3 "2020-10-03T09:08:04Z")
Thanks for reply! šŸ™‚ Yes I will remove the bed and check, and if the problem is still the same I can post a video. (I am away for a week, so it will take some time before I can play more with my Snapmaker ā˜¹ ) ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 3, 2020, 9:12am UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/4 "2020-10-03T09:12:08Z")
PS: I ran two 5 hrs prints yesterday before I left, they both turned out perfect! šŸ™‚ But the pieces was printed in the center of the bed and not large enough so that the axis travelled into the bumpy area. ---
**Author:** ![Flid](https://avatars.discourse-cdn.com/v4/letter/f/eada6e/32.png) [@Flid](https://forum.snapmaker.com/u/Flid)\ **Post date:** [October 3, 2020, 2:51pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/5 "2020-10-03T14:51:25Z")
Iā€™ve got the same issue, really annoying. I donā€™t think it happens on the same position every time, but somewhere near the middle. Also it doesnā€™t happen every time, but occasionally, especially when moving far and then returning. Sometimes itā€™s just an audible bump, sometimes I can even see the platform jumping a few mm up. It has broken my CNC mill once, when it was nearly finished, the table has jumped up, so I found the mill stuck almost 2 mm into the surface, much further than the print should go. Considering it doesnā€™t happen all the time, itā€™s quite challenging to film it, but I got something here: [https://yadi.sk/i/tAQQINqiGpEqfA](https://yadi.sk/i/tAQQINqiGpEqfA) I did re-tighten all the screws on the platform and bed, nothing has changed. The issue is critical, it breaks CNC mills and ruins prints, making the printer pretty much unusable. ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 3, 2020, 3:41pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/6 "2020-10-03T15:41:33Z")
Hi Flid, I looked at your video, seems like we have the same problem! ā˜¹ After I ran a few more tests it looks like it doesnā€™t happen at the same spot, but changes a bit depending on which way the bed travels. I can also see the bed shake when I hear the bumpā€¦ Relly hope there is a way to fix this! šŸ¤” šŸ¤Ø ---
**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\ **Post date:** [October 4, 2020, 9:58am UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/7 "2020-10-04T09:58:40Z")
Here are some threads about Linear Module defects, unfortunately you will have to contact [support@snapmaker.com](mailto:support@snapmaker.com) : > [@A350 Bed rises and falls even during slow speeds](https://forum.snapmaker.com/t/a350-bed-rises-and-falls-even-during-slow-speeds/6163): > > [Here is a video.](https://youtu.be/YBMUMF7F9NI) Watch the corner against the Z arm, and itā€™s quite noticeable it goes up and down. Am I the only one seeing this? > [@Linear module stopped working after third print](https://forum.snapmaker.com/t/linear-module-stopped-working-after-third-print/8240): > > I took delivery of my A350 a few days ago. Two test prints were successful. Todayā€™s print, the third, didnā€™t finish successfully. About three vertical centimetres before the end of the print, there was a bulge, suggesting a problem on the Z axis. At the end of the job, the percentage completion stayed at 100% for over an hour, with the print nozzle still on the printed piece, before I turned the machine off. Since then, one of the vertical linear modules no longer works. There is no motionā€¦ > [@Y Linear module Fault](https://forum.snapmaker.com/t/y-linear-module-fault/7486): > > @Edwin I think I have a similar fault with my A250 linear module as mentioned in another post. [[A250 Y axis fault] ](https://www.youtube.com/watch?v=V0Dw2sEQj60) the Y axis is making a terrible noise and it seems to twist when it moves like one of the motors is not working. I have reseated all of the cables for the Y axis and have updated the firmware to 1.9. I have attempted to recalibrate the bed and the print nozzle has left a deep impression in the top left of the print bed - just visible on the ā€˜250 white lineā€™ next to ā€¦ > [@HELP ! My A350 Y-axis linear modules are not functioning correctly](https://forum.snapmaker.com/t/help-my-a350-y-axis-linear-modules-are-not-functioning-correctly/8924): > > I received my SnapMaker A350 last week, but only 2 of the 3 packages arrived and the 3rd one containing the Enclosure showed no activity on the tracking number, so I created support ticket # 43415. A few days later the 3rd tracking number was updated with actual shipping info and yesterday I received the box with the enclosure. After putting the A350 together I ran a few calibrations and everything seemed to function correctly, so I downloaded Luban and was going to print the demo vase. After gā€¦ ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 5, 2020, 3:17pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/8 "2020-10-05T15:17:38Z")
I have now tried to remove the base and let the axis move freely. When testing without anumything on, I did not hit any bumps on the axis. I then loosened the y axis modules and assembled the base with loose screws and tested again - still fine. I then tightened the bed and moved the y-axis to the end and tightened the screws on the Y module, and the travelled to the other end and tightened the screws there. I then tightened all screws. After everything was tightened, I ran the test again - still fine! I then set up to do a new 3D print and ran the calibration, and suddenly i heard the horrible noise again! ā˜¹ I did another test of manually moving the axis, and the problem is back and still as bad as before ā˜¹ ---
**Author:** ![d90](https://avatars.discourse-cdn.com/v4/letter/d/41988e/32.png) [@d90](https://forum.snapmaker.com/u/d90)\ **Post date:** [October 5, 2020, 5:26pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/9 "2020-10-05T17:26:20Z")
Hey there, Have a look at this thread: > [@Clunks, stuttering, negative bed temps, lost connections. General disappointment](https://forum.snapmaker.com/t/clunks-stuttering-negative-bed-temps-lost-connections-general-disappointment/9858): > > Hello, I received my A350 a couple weeks ago and finally found the time to set it up. After carefully and smoothly assembling the unit, loading filament and leveling the bed for the first time, I was met with a number of issues while trying run the first test print vase. I noticed that while auto-bed leveling, homing after boot, or in the preparation phase before a print, the bed motion (Y) would ā€œclunkā€ when it passed roughly the middle of its travel. After paying attention a little more ā€¦ Spoiler alertā€¦ there are no solutions in itā€¦ but misery loves company, right? Perhaps it will help fill in all the troubleshooting blanks for somebody somewhere whenever support decides to tackle what seems to be a major QA problem for these units. ---
**Author:** ![General\_Tux](https://avatars.discourse-cdn.com/v4/letter/g/49beb7/32.png) [@General\_Tux](https://forum.snapmaker.com/u/General_Tux)\ **Post date:** [October 6, 2020, 3:04pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/10 "2020-10-06T15:04:30Z")
Hi all, I just received my A350 a couple weeks ago. Iā€™ve been able to print several small items in the center ~75mm of X and Y axis travel, however when I have tried larger prints, I noticed problems with the bed leveling. In trying to troubleshoot those problems, Iā€™ve experienced the same type of issues you described here, but only during calibration (so far). Randomly during calibration, Iā€™ve had the machine make a think sound and then the Y-axis gets stuck, forcing me to turn off the machine since there isnā€™t an emergency stop on the touch screen. This has happened three times now, each time in a different location in the Y-axis. The first time was near the center of travel, the next time near the back end of travel and the most recent time is was at the front of travel (close to Y-axis home). So far, this has only happened during calibration. Every time this has happened, Iā€™m able to move the Y-axis manually from the touch screen and it always homes successfully. Prints also have been able to complete fine without any apparent Y-axis issues, so far at least. I have the A350 in its enclosure so there should not be anything getting in the way of the Y-axis. Iā€™ve also completely disassembled the Y-axis during my troubleshooting and Iā€™ve not found anything that can explain this behavior. Does anyone have any further suggestions for how to troubleshoot this beyond what has already been said or should I contact support directly? Thanks! ---
**Author:** ![brent113](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/brent113/32/11114_2.png) [@brent113](https://forum.snapmaker.com/u/brent113)\ **Post date:** [October 6, 2020, 4:07pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/11 "2020-10-06T16:07:03Z")
Iā€™m really curious what the root cause of these turns out to be. The circuits are very simple, Iā€™m thinking it has to be something mechanical? Guide rail bearings or something? ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 7, 2020, 1:26pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/12 "2020-10-07T13:26:50Z")
Hi, I am very curious too! Must be something mechanicalā€¦ almost seem like the axis does not move completely parallel, so that there is some slack that suddenly ā€œspringā€ back when the tension gets to high. šŸ¤” ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 7, 2020, 1:31pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/13 "2020-10-07T13:31:26Z")
I made a video of the problem: [https://youtu.be/6uJt54c3fc8](https://youtu.be/6uJt54c3fc8) ---
**Author:** ![ITmaze](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/itmaze/32/6225_2.png) [@ITmaze](https://forum.snapmaker.com/u/ITmaze)\ **Post date:** [October 7, 2020, 1:43pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/14 "2020-10-07T13:43:04Z")
Are both actuators moving without the build plate attached? ---
**Author:** ![General\_Tux](https://avatars.discourse-cdn.com/v4/letter/g/49beb7/32.png) [@General\_Tux](https://forum.snapmaker.com/u/General_Tux)\ **Post date:** [October 7, 2020, 2:00pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/15 "2020-10-07T14:00:08Z")
Just a quick update on my situation. I was able to print another small part (50 x 50 x 15 mm) last night. Iā€™m really curious why this problem only appears during calibration on my machine. I also contacted support, hopefully they can resolve it soon. ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 7, 2020, 4:31pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/16 "2020-10-07T16:31:53Z")
I can also print small parts without any issuesā€¦ looks like the axis have to travel at least half or maybe 2/3 of the way before the problem occurs. ---
**Author:** ![brent113](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/brent113/32/11114_2.png) [@brent113](https://forum.snapmaker.com/u/brent113)\ **Post date:** [October 7, 2020, 4:34pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/17 "2020-10-07T16:34:28Z")
Just a thought I had, although I realize this is probably not the issue. If the machine is off and you manually push the bed all the way against both of the Y stops so both of the modules are definitely in alignment with each other, does that change anything? Also does it happen at all travel speeds? Can you try it at slow and fast speeds? ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 7, 2020, 4:43pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/18 "2020-10-07T16:43:12Z")
Yes, I have tried to push manually all the way to the end, but I canā€™t find any problems there. Also when I took it apart I ran the machine back and forth while gradually tightening the screws, so I do not think this is the problem. I have not tried on different speedsā€¦ Im not very familiar with the machine yet so Iā€™m not sure how change the speed. ---
**Author:** ![brent113](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/brent113/32/11114_2.png) [@brent113](https://forum.snapmaker.com/u/brent113)\ **Post date:** [October 7, 2020, 5:05pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/19 "2020-10-07T17:05:55Z")
Watched the video several times. Sounds to me like the stepper motor is skipping a step, especially considering the right side jumps forward or backwards when it moves. Are the modules parallel? I see you said the problem goes away when you removed the bed. When you assembled the Y modules to the base plate did you leave the screws loose until the bed was assembled? Could you try loosening the screws under the Y modules, moving the bed around with loose screws, and let me know if the problem is still present? Also, if it goes away with loose module mount screws try pushing the bed against the endstops like before, then driving the bed position to somewhere in the middle using the controller and retightening the screws - does the problem come back? ---
**Author:** ![Podle](https://avatars.discourse-cdn.com/v4/letter/p/e8c25b/32.png) [@Podle](https://forum.snapmaker.com/u/Podle)\ **Post date:** [October 7, 2020, 5:09pm UTC](https://forum.snapmaker.com/t/bump-in-y-axis/10017/20 "2020-10-07T17:09:21Z")
Thanks, good suggestion! I will try šŸ™‚ [Next page](https://forum.snapmaker.com/t/bump-in-y-axis/10017.md?page=2)