# Auto Focus Failed

**URL:** <https://forum.snapmaker.com/t/auto-focus-failed/13095>\
**Category:** Snapmaker 2.0 (3-in-1)\
**Created:** [December 21, 2020, 5:50pm UTC](https://forum.snapmaker.com/t/auto-focus-failed/13095 "2020-12-21T17:50:09Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![Somnium](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/somnium/32/9800_2.png) [@Somnium](https://forum.snapmaker.com/u/Somnium)\
**Post date:** [December 21, 2020, 5:50pm UTC](https://forum.snapmaker.com/t/auto-focus-failed/13095/1 "2020-12-21T17:50:09Z")

</div>

When I calibrate the Lasermodul it won’t choose the best engraved line because the camera can’t see it right

thx for help

---

<div class="post-metadata">

**Author:** ![stefix](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/stefix/32/8616_2.png) [@stefix](https://forum.snapmaker.com/u/stefix)\
**Post date:** [December 21, 2020, 6:56pm UTC](https://forum.snapmaker.com/t/auto-focus-failed/13095/2 "2020-12-21T18:56:18Z")

</div>

OK but to help infos are needed, please explain your problem a little closer.

---

<div class="post-metadata">

**Author:** ![Somnium](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/somnium/32/9800_2.png) [@Somnium](https://forum.snapmaker.com/u/Somnium)\
**Post date:** [December 21, 2020, 9:53pm UTC](https://forum.snapmaker.com/t/auto-focus-failed/13095/3 "2020-12-21T21:53:55Z")

</div>

Sorry for my late reply  
I dont have any infos when the camera should pick the best line that has been engraved it says it faild because auto focus can not see the lines

---

<div class="post-metadata">

**Author:** ![brent113](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/brent113/32/11114_2.png) [@brent113](https://forum.snapmaker.com/u/brent113)\
**Post date:** [December 21, 2020, 9:56pm UTC](https://forum.snapmaker.com/t/auto-focus-failed/13095/4 "2020-12-21T21:56:11Z")

</div>

I also had that issue, and ended up disabling auto calibration. It really doesn’t take any longer to use manual calibration, and in my opinion gets you a more consistent calibration. It’s in the touchscreen settings, and you just select the thinnest line.

---

<div class="post-metadata">

**Author:** ![Somnium](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/somnium/32/9800_2.png) [@Somnium](https://forum.snapmaker.com/u/Somnium)\
**Post date:** [December 21, 2020, 9:59pm UTC](https://forum.snapmaker.com/t/auto-focus-failed/13095/5 "2020-12-21T21:59:07Z")

</div>

Ok yeah i also did that and takes not much time but i choosed the middle line. so you recommend the thinest line?

---

<div class="post-metadata">

**Author:** ![brent113](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/brent113/32/11114_2.png) [@brent113](https://forum.snapmaker.com/u/brent113)\
**Post date:** [December 21, 2020, 9:59pm UTC](https://forum.snapmaker.com/t/auto-focus-failed/13095/6 "2020-12-21T21:59:49Z")

</div>

Here’s what I do in a bit more detail. If the line is too close to the left or right you should pick the far left or far right line (whatever’s closest) and re-run calibration again.

> [@Comments on Quick Start Guide and Laser User Manual](https://forum.snapmaker.com/t/comments-on-quick-start-guide-and-laser-user-manual/10194/11):
>
> The thinnest line indicates the correct focus. It can be confirmed by looking left and right about 4 lines and checking those lines are equal sized. I chose the one marked in green. And the yellow marked lined 4 to each side are the same size. [image] I almost chose the one immediately to the right of the one marked in green, but comparing the size of the lines 4 away from that there’s a big difference. In that case the line 4 to the right is noticeably wider than the one 4 to the left. [ima…

---

<div class="post-metadata">

**Author:** ![Somnium](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/somnium/32/9800_2.png) [@Somnium](https://forum.snapmaker.com/u/Somnium)\
**Post date:** [December 21, 2020, 10:01pm UTC](https://forum.snapmaker.com/t/auto-focus-failed/13095/7 "2020-12-21T22:01:51Z")

</div>

Thanks really helpful 👍🏼
