# A350 Stopped an goes to home after short time of Start **URL:** \ **Category:** Snapmaker2.0 Troubleshooting guides\ **Created:** [November 2, 2025, 5:52pm UTC](https://forum.snapmaker.com/t/a350-stopped-an-goes-to-home-after-short-time-of-start/40254 "2025-11-02T17:52:34Z")\ **Posts on this page:** 6\ **Page:** 1
**Author:** ![Jokim](https://avatars.discourse-cdn.com/v4/letter/j/7ea924/32.png) [@Jokim](https://forum.snapmaker.com/u/Jokim)\ **Post date:** [November 2, 2025, 5:52pm UTC](https://forum.snapmaker.com/t/a350-stopped-an-goes-to-home-after-short-time-of-start/40254/1 "2025-11-02T17:52:34Z")
My Snapmaker A350 suddenly stops the Projekt short after start printing. I print the same Projekt as befor whithout changes. Why ?? If i restart the konfiguration in luban it will run for one job. ---
**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\ **Post date:** [November 3, 2025, 4:15pm UTC](https://forum.snapmaker.com/t/a350-stopped-an-goes-to-home-after-short-time-of-start/40254/2 "2025-11-03T16:15:02Z")
Export your logs and share the data. [https://wiki.snapmaker.com/en/Snapmaker\_2/manual/export\_logs](https://wiki.snapmaker.com/en/Snapmaker_2/manual/export_logs) ---
**Author:** ![paradoxus](https://avatars.discourse-cdn.com/v4/letter/p/9f8e36/32.png) [@paradoxus](https://forum.snapmaker.com/u/paradoxus)\ **Post date:** [November 8, 2025, 10:28am UTC](https://forum.snapmaker.com/t/a350-stopped-an-goes-to-home-after-short-time-of-start/40254/3 "2025-11-08T10:28:11Z")
i downloaded the new snapmaker orca yesterday and i had the same happening. it began with the starting routine, heating up, going to the edge of the printbed and priming. after priming it stopped the print. ---
**Author:** ![paradoxus](https://avatars.discourse-cdn.com/v4/letter/p/9f8e36/32.png) [@paradoxus](https://forum.snapmaker.com/u/paradoxus)\ **Post date:** [November 14, 2025, 10:08am UTC](https://forum.snapmaker.com/t/a350-stopped-an-goes-to-home-after-short-time-of-start/40254/4 "2025-11-14T10:08:40Z")
with prusaslicer i have no problems. even the color changes work now ---
**Author:** ![christian\_mussatto](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/christian_mussatto/32/21075_2.png) [@christian\_mussatto](https://forum.snapmaker.com/u/christian_mussatto)\ **Post date:** [December 17, 2025, 2:11am UTC](https://forum.snapmaker.com/t/a350-stopped-an-goes-to-home-after-short-time-of-start/40254/5 "2025-12-17T02:11:01Z")
[SC\_86.zip](https://forum.snapmaker.com/uploads/short-url/jJvBV9bo5m3TJG473yXsDI7f4K2.zip) (863.3 KB) I’m sharing the logs. I have the same issue; it stops halfway through the process. I hope there’s a solution. ---
**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\ **Post date:** [December 17, 2025, 7:33pm UTC](https://forum.snapmaker.com/t/a350-stopped-an-goes-to-home-after-short-time-of-start/40254/6 "2025-12-17T19:33:34Z")
Hard to say, are we talking about your 2w laser or 3dp module, which time the error occurs would also be helpful. I see a lot wireless printing (at least I think this discover requests are from wireless connection). And I see failed unpacked gcode . I see your firmware is not up to date. Update your firmware please and tell us some more stuff, especially which slicer. Try to send the gcode to the machine and print it local. Anyway, you could reach out to snapmaker support they are really helpful. email [support@snapmaker.com](mailto:support@snapmaker.com) ticket [https://support.snapmaker.com/hc/en-us/requests/new](https://support.snapmaker.com/hc/en-us/requests/new)