# 99% error when using Simplify3d

**URL:** <https://forum.snapmaker.com/t/99-error-when-using-simplify3d/11691>\
**Category:** Snapmaker 2.0 (3-in-1)\
**Created:** [November 20, 2020, 2:31pm UTC](https://forum.snapmaker.com/t/99-error-when-using-simplify3d/11691 "2020-11-20T14:31:59Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![PliskinAJ](https://avatars.discourse-cdn.com/v4/letter/p/fbc32d/32.png) [@PliskinAJ](https://forum.snapmaker.com/u/PliskinAJ)\
**Post date:** [November 20, 2020, 2:31pm UTC](https://forum.snapmaker.com/t/99-error-when-using-simplify3d/11691/1 "2020-11-20T14:31:59Z")

</div>

I have updated the firmware on the printer but I am still getting a 99% error. Right now I’m getting it when ever I send G-code from Simplifiy3d. Anyone find a remedy for this?

---

<div class="post-metadata">

**Author:** ![Atom](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/atom/32/5608_2.png) [@Atom](https://forum.snapmaker.com/u/Atom)\
**Post date:** [November 20, 2020, 3:07pm UTC](https://forum.snapmaker.com/t/99-error-when-using-simplify3d/11691/2 "2020-11-20T15:07:14Z")

</div>

Remove the comments from your post gcode script

---

<div class="post-metadata">

**Author:** ![PliskinAJ](https://avatars.discourse-cdn.com/v4/letter/p/fbc32d/32.png) [@PliskinAJ](https://forum.snapmaker.com/u/PliskinAJ)\
**Post date:** [November 20, 2020, 3:14pm UTC](https://forum.snapmaker.com/t/99-error-when-using-simplify3d/11691/3 "2020-11-20T15:14:51Z")

</div>

I’ll give it a shot, thanks.

---

<div class="post-metadata">

**Author:** ![dave4snap](https://avatars.discourse-cdn.com/v4/letter/d/b9bd4f/32.png) [@dave4snap](https://forum.snapmaker.com/u/dave4snap)\
**Post date:** [November 20, 2020, 7:05pm UTC](https://forum.snapmaker.com/t/99-error-when-using-simplify3d/11691/4 "2020-11-20T19:05:35Z")

</div>

I had the same problem but then I realized that the last gcode when Luban slices is an M84 to turn off motors. My ending script did not have that as the last command. When I modified my Simplify 3D ending script to put the M84 as the last command, the problem was solved and my prints now run to 100%. Here is my current ending script.  
;===== BEG SNAP STOP  
G90 ; absolute positioning  
G92 E0 ; Set extruder position  
G1 E-2 F300 ; retract filament to release pressure  
M107 ; turn off cooling fan  
M104 S0 ; turn off extruder  
M140 S0 ; turn off bed  
G1 Z235 F3000 ; move Z up  
G1 X0 F3000 ; move X to min endstops  
G1 Y250 F3000 ; move bed forward  
;===== END SNAP STOP  
M84

---

<div class="post-metadata">

**Author:** ![PliskinAJ](https://avatars.discourse-cdn.com/v4/letter/p/fbc32d/32.png) [@PliskinAJ](https://forum.snapmaker.com/u/PliskinAJ)\
**Post date:** [November 22, 2020, 11:39pm UTC](https://forum.snapmaker.com/t/99-error-when-using-simplify3d/11691/5 "2020-11-22T23:39:37Z")

</div>

Some of my end comments text wrapped with out me knowing so the second line didn’t have a comment break I thought the window just text wrapped but it didn’t. Thanks for the help. Once that was done I don’t have the 99% error anymore.
