# 3D Print Module 1st Use (Luban Error) **URL:** \ **Category:** Snapmaker2.0 Troubleshooting guides\ **Created:** [March 20, 2024, 11:15pm UTC](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380 "2024-03-20T23:15:43Z")\ **Posts on this page:** 7\ **Page:** 2
**Author:** ![zkidez](https://avatars.discourse-cdn.com/v4/letter/z/3be4f8/32.png) [@zkidez](https://forum.snapmaker.com/u/zkidez)\ **Post date:** [March 24, 2024, 5:47pm UTC](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380/21 "2024-03-24T17:47:52Z")
![image](https://us1.discourse-cdn.com/flex022/uploads/snapmaker/original/3X/4/0/40894b9b65f763ec75355deb332e02f6a87a75c7.png) Good thats was the Issue. đź‘Ť if you have the z axis to high Bug you need to print a small thing , swipe to te left ( so right side of display is visible ) here you have to adjust the z offset ( steps are 0,05 0,1 0,2 ) in my case Dual extruder is always ~0,3 to high, so i correct is by this setting ( Auto Calibration is not perfect -.- ) But if you know the issues you can just setup it counterwise. by the way, this setting will also be saved for the next prints , so you will change it in the Firmware ---
**Author:** ![craftycarper](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/craftycarper/32/20513_2.png) [@craftycarper](https://forum.snapmaker.com/u/craftycarper)\ **Post date:** [March 25, 2024, 4:31am UTC](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380/22 "2024-03-25T04:31:12Z")
Z axis at the top of travel when you run auto-calibrate, that’s not good. The auto-calibrate should ask you to set bed temp then move down to within 10mm or so of the heated bed before doing the sensor run. BTW I have gone into settings and increased the number of calibration points from the default 3x3 to 5x5. This gives much better bed leveling results. Give that a go and see what happens. ---
**Author:** ![imanafman](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/imanafman/32/11751_2.png) [@imanafman](https://forum.snapmaker.com/u/imanafman)\ **Post date:** [March 25, 2024, 11:32am UTC](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380/23 "2024-03-25T11:32:35Z")
I have changed the setting to 5x5 and resorted to lowering the z axis once I load the G-Code, thank you for the advice. ---
**Author:** ![reesesm2000](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/reesesm2000/32/23742_2.png) [@reesesm2000](https://forum.snapmaker.com/u/reesesm2000)\ **Post date:** [March 26, 2024, 11:33pm UTC](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380/24 "2024-03-26T23:33:29Z")
Not sure if anyone else mentioned this but Cura is a far more capable product than Luban. It does a way better job at generating GCode and has a ton more features. I started out expecting Luban to be a good product based on the price of the Artisan but it is just very inferior. ---
**Author:** ![JohnFiott](https://avatars.discourse-cdn.com/v4/letter/j/5f9b8f/32.png) [@JohnFiott](https://forum.snapmaker.com/u/JohnFiott)\ **Post date:** [March 27, 2024, 10:18am UTC](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380/25 "2024-03-27T10:18:48Z")
you could maybe at least go part way by using the new option that allows moving the head to a central position to change the toolhead. its in the menu options. (Note I just installed the new firmware after about a year of non use and found this option had been added. I like it). ---
**Author:** ![imanafman](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/imanafman/32/11751_2.png) [@imanafman](https://forum.snapmaker.com/u/imanafman)\ **Post date:** [March 27, 2024, 11:41am UTC](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380/26 "2024-03-27T11:41:26Z")
Thanks for the reply, I was focussing on the Luban just toi get me into the 3D printing side of the machine, since in 3 years of owning it, I never touched it, Last night after two failed attempts of doing the “Benchy” (The 2nd print almost completed), I did a calibration cube after changing a few minor settings and it came out darn-near perfect. ---
**Author:** ![imanafman](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/imanafman/32/11751_2.png) [@imanafman](https://forum.snapmaker.com/u/imanafman)\ **Post date:** [March 27, 2024, 11:42am UTC](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380/27 "2024-03-27T11:42:34Z")
I went to “Manual” Calibration and started getting the prints to work. Thanks for the insight! [Previous page](https://forum.snapmaker.com/t/3d-print-module-1st-use-luban-error/35380.md?page=1)