# 10W laser in Ray System

**URL:** <https://forum.snapmaker.com/t/10w-laser-in-ray-system/35636>\
**Category:** Ray (Laser)\
**Created:** [April 19, 2024, 10:08am UTC](https://forum.snapmaker.com/t/10w-laser-in-ray-system/35636 "2024-04-19T10:08:22Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![dunmac25](https://avatars.discourse-cdn.com/v4/letter/d/edb3f5/32.png) [@dunmac25](https://forum.snapmaker.com/u/dunmac25)\
**Post date:** [April 19, 2024, 10:08am UTC](https://forum.snapmaker.com/t/10w-laser-in-ray-system/35636/1 "2024-04-19T10:08:23Z")

</div>

Has anyone tried using the 10W laser module in the Ray frame ?  
I am seriously looking at this as I cannot get similar results with the 40 W Ray unit as I can using the 10W unit in my A350.  
I am looking to replicate the results of the 350 on a bigger scale.  
Any info on the set up, controls and settings I need, would be appreciated  
I will post my thoughts on my albeit limited experience with the Ray unit

Thanks in advance

---

<div class="post-metadata">

**Author:** ![spucky](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/spucky/32/25910_2.png) [@spucky](https://forum.snapmaker.com/u/spucky)\
**Post date:** [April 19, 2024, 5:25pm UTC](https://forum.snapmaker.com/t/10w-laser-in-ray-system/35636/2 "2024-04-19T17:25:03Z")

</div>

I am struggling also a bit on glass with the 40W module.

But similar to the Artisan the firmware of the Ray must support the 10W module. Not sure if Snapmaker does this have in focus.

---

<div class="post-metadata">

**Author:** ![xchrisd](https://sea2.discourse-cdn.com/flex022/user_avatar/forum.snapmaker.com/xchrisd/32/1503_2.png) [@xchrisd](https://forum.snapmaker.com/u/xchrisd)\
**Post date:** [April 20, 2024, 8:01am UTC](https://forum.snapmaker.com/t/10w-laser-in-ray-system/35636/3 "2024-04-20T08:01:09Z")

</div>

> [@10W Laser Module Quick-Swap Plate and Calibration Target Model for Snapmaker Ray](https://forum.snapmaker.com/t/10w-laser-module-quick-swap-plate-and-calibration-target-model-for-snapmaker-ray/33930):
>
> Hello Makers! We’ve received user feedback expressing the desire to use the 10W laser module with Snapmaker Ray. However, currently, there’s no corresponding quick-swap plate available to attach the toolhead bracket on Ray. Additionally, some users provided feedback about losing their calibration target and being unable to recover it. To address this, our Product Team has designed a printable quick-swap plate that will assist you in integrating the 10W laser module with Ray. We have also desig…

> [@Ray Wiki Content Updates](https://forum.snapmaker.com/t/ray-wiki-content-updates/33980/3):
>
> Dec 22 2023 New Content 10W Laser Module [Installing the 10W laser module on Ray](https://wiki.snapmaker.com/snapmaker_ray/manual/install_10w_laser_module) 10W/20W/40W Laser Module [Adjusting the laser height for 3-axis and 4-axis machining on Ray](https://wiki.snapmaker.com/snapmaker_ray/manual/adjust_laser_height) Maintenance [Cleaning the heat dissipation fan](https://wiki.snapmaker.com/general/maintenance/clean_heat_dissipation_fan_of_20w_&_40w_laser_module)[Cleaning the steel strip](https://wiki.snapmaker.com/en/general/maintenance/clean_steel_strip)[Cleaning the laser lens protector of the 10W/20W/40W Laser Module](https://wiki.snapmaker.com/general/maintenance/clean_laser_lens_protector_of_10w&20w&40w_laser)[Replacing the laser lens protector of the laser module](https://wiki.snapmaker.com/general/maintenance/replace_the_laser_lens_protector_of_10w&20w&40w_laser)[Cleaning the laser platform of the 20W/40W laser module](https://wiki.snapmaker.com/general/maintenance/clean_the_20w_40w_laser_platform)[Cleaning the bottom cover of the 20W/40W laser module](https://wiki.snapmaker.com/general/maintenance/clean_the_20w_40w_bottom_cover) …